![]() ![]() |
Audio Asylum Thread Printer Get a view of an entire thread on one page |
For Sale Ads |
170.215.154.174
IF YOU DARE!!!
Room treatments! DIY Risch recipes 8 4'/18" diameter and 6 4'X2'X4" thick panelsModify both Conrad Johnson amps by adding chassis mount IEC to accept "other" cords. Dremel tool required
Cardas caps on unused RCA jacks
ISOLATION! Herbies and other DIY wood slabs/blocks and deflex. One or the other under every component
Herbies Big fat black dots under speakers - nice
Herbies CD mats - work well with my new transport, Philips transport didn't like them
Oyaide outlets AND WPC-Z outlet cover. I have said before the cover, which costs more than the outlets may be more important.
DIY Oyaide Outlet strip w/R-1's. My closest outlet to the rig is 8 feet away. I have an 8 gauge cable to the strip by the rig.
Richard Gray 600, got it for free!
PS Audio P-300 - essential for sources in my opinion!
PS Audio Noise Harvesters - 3, two is enough, one is for sale.
The last three aren't technically tweaks but made marked improvements.
All cables unshielded - smoother.......
All Safety grounds lifted - this was huge! A famous well respected engineer here says the safety grounds act as an antenna for noise. I agree!
Al Sekalas R/C filters for ACAl Sekalas R/C speaker filters - WOW!!
Small brilliant pebbles on power cord at IEC of HF amp -wow!
Try cables before you buy them. You'll find one that helps a lot.
I'm sure I'm forgetting something. They have all helped or I would have removed them from the system
ET
Question "Authority", the mainstream media sucks - Go Independent and hold BOTH parties accountable instead of just the other guys!
I need music to help forget the reality of today
Edits: 03/05/09Follow Ups:
;-)
Sand filled balloons under gear
Blue tak on caps
Naked DAC.....took cover off
Dynomat inside speakers
re-wired speakers
Karma Means Never Having To Say You're Sorry
INSTALL SNUBBERS ON THE OUTPUT OF THE PS BRIDGE's. A GENERIC SNUBBER CONSISTS OF A .01 uF STACKED FILM CAP IN SERIES WITH A 5 OHM C.C. RESISTOR WITH THE CAP ON THE BRIDGE OUTPUT AND THE RESISTOR CONNECTED TO GD.
HAPPY LISTENING !
but not on schottky doides
So far:
Speaker Spikes
Panamax M10-HT-PRO
Synergistic Research Tesla Quad Speaker Cable (Bi-Wired)
Gut Wire B-16 AC Cable (Most likely will get 2 more)
Transparent Link 200 Interconnects (Will be replaced with Synergistic Research Tesla Sterling Discrete's)
MFSL Shine-Ola
Looking into:
Cardas RCA Caps
Black Diamond Racing Cones (CD Player)
I won't bore the world with all the tweaks I have performed. The one that I have found that has always yielded results in all of my equipment is to replace the fuses in the components with ceramic fuses. Not exotic audiophile fuses - just generic "ceramic" fuses.
I have been able to purchase the ones I needed from the local Sears Hardware store (not the department store). The fuses are in the trays where screws, nuts, and bolts are kept. It is quite possible these fuses nay be found at electronic or hardware stores.
For a minimal amount of expense and effort this tweak has yielded miraculous results.
DaveT
What properties of ceramic fuses do you think improves the sound?
*
Question "Authority", the mainstream media sucks - Go Independent and hold BOTH parties accountable instead of just the other guys!
I need music to help forget the reality of today
What more reason do you need?
HiFi Tuning Fuses are #1, and no I don't pay special attention to their direction (that should set Norm off :-)
Ferrite blocks on power cables.
Keeping all cables off the carpet.
Mr. Clean magic eraser for stylus cleaning.
Tube rolling
AIVS record cleaning regimen
For starters
I asked my question because I know full well that there is no consensus.
Post a Followup:
FAQ |
Post a Message! |
Forgot Password? |
|
||||||||||||||
|
This post is made possible by the generous support of people like you and our sponsors: