|
Audio Asylum Thread Printer Get a view of an entire thread on one page |
For Sale Ads |
71.234.12.142
In Reply to: I'm sure you're right, but that's not what I said. posted by Triode_Kingdom on April 20, 2007 at 11:20:04:
so you agree that the choke could have some benefit, and were simply pointing out that the benefits heard are not the result of reactivness of the inductor at ripple frequency?
Follow Ups:
> so you agree that the choke could have some benefit"Could" being the operative word, yes, but then so could a 5Hy or 10H. Most important, none of this requires oddball, low-R components. The dynamics of the amplifier aren't enabled by drawing power directly from the rectifier, but rather from having sufficient DC reserve. I don't care how many veterinarians say otherwise, low-R is no breakthrough.
do you have any guestimates on the shunt capacitance of a 5-10hy choke vs. something like 50mhy?
> do you have any guestimates on the shunt capacitance of a 5-10hy choke vs. something like 50mhy?The shunt capacitance of a large choke is probably something under 0.001 uF, but that's purely a guess. I suppose a small choke might be on the order of 100 pF or so. How does this relate to the discussion?
so the smaller valued choke may actually provide more impedance as frequency goes up.what does he frequency content of a cap input filter look like?
> so the smaller valued choke may actually provide more impedance as frequency goes upNot unless you're concerned about components in the upper MHz region. If you are, I suggest that you also consider the extremely small reactance of even a 10 uF filter cap at those frequencies, and the rapidly diminshing (i.e. miniscule) energy contained in those upper harmonics. All in all, a larger choke, 10-20 Hy or so, will be much more effective than, say, a 22 mH at the frequencies where XL is needed.
My view has always been that low DCR becomes important when the amp draws variable current depending on the signal, i.e. PP class AB or B. That's when you need minimum sag. However, for class A I would agree with you. That's when a good reservoir cap should provide all the DC needs and it shouldn't really matter (within reason) what comes before it in the PS.
I tried the choke input filter set up going with as low a dcr as Lundal could provide and found that to me it was much better. This is in a single ended parallel 845 design running at 1250 volts. I was suprised. As for low dcr I set no controls for that other than what was mentioned. Power transformers wher from same manufacturer just different voltages. I was surprized.T Willman
> > I tried the choke input filter set up going with as low a dcr as Lundal could provide... which specific choke did you use, what other changes (if any) were made at the same time, and how did you determine the results to be better? Can you post a schematic?
I am sorry but I think the directions for posting picture and schematics are so simple that I can't figure it out. Could someone give dummy'd down but detailed never the less instructions please. T Willman
Yes I will show my shi#. I have two pairs of amps each very close in size shape and circuit. There are only two differences. Please be patient I will post them shortly; I have never done this I will try to have it tonight. T Willman
Tom,Tell us please, does your 845 amp run in Class A1, where Ray thinks it " makes no difference ", ( but I always find it to be otherwise! ).
Almost 80% of my low DCR experiments have been conducted in A1 amp stages, both P-P ( mostly ) and SE stages, but Ray seems to give 'ole LowMu NO SLACK or appropriate recognition of this work and Forum-posted result, as it opposes what he has read in some book....probably RDH4. He constantly likes to quote book-learned stuff without always experimentally finding out for himself. But he is basically a nice chap - none the less, unlike a couple of others up here who I don't have to name.
Jeff, my response was not aimed at you. I meant what I said, which was that IMHO with a big enough reservoir cap and no great variation in current demand, voltage sag shouldn't be a problem. Now, that is not to say that a reservoir cap solves all problems for class A. I'm not saying there's no point in refining the PS to make it sound better. Nobody wants to listed to HF noise, mains-borne inductive spikes, SS diode hash, poor quality electrolytics or any other undesirable effects that can be caused by a PS that's not doing its job very well.Once you have current demand that can vary, then you need a stiffer PS to avoid the dreaded sag (which may be loved by some guitar players but not by HiFi enthusiasts). Obviously, you're not going to achieve this with a PS with high DCR unless you use active regulation, which most people would rather avoid.
The good veterinarian has fixated on Low DCR as a prerequisite cure-all. It's a preemptive strike against noise, poor dynamics, narrow soundstage, lifeless amps, etc. etc. With apparently no legitimate evidence whatsoever, not even valid testing, he is not only intent on converting the world to his view, but on taking credit for this nonexistent invention. You will have to be satisfied with warning others. I predict common sense will continue to elude this individual.
URL below.T_K gets VERY quiet when we ask for HIS credentials.
T_K reminds me somewhat of the anger of the late Mr. Cho.
T_K does not speak to us - of his credentials.
Properly introduce yourself. "Question Mark" all over again ??
Jeff
That post makes me ANGRY!"T_K gets VERY quiet when we ask for HIS credentials."
Are you using the royal 'we' or do you actually imagine that other people besides yourself feel the need to know? If you do, then I think you're seriously mistaken."T_K reminds me somewhat of the anger of the late Mr. Cho."
How DARE you compare someone on this forum to a mass muderer with a psychopathically antisocial personality, just because they hold different views to your own? This is rudeness in the extreme, and a sign of your own inadequacies.
credentials are earned, and given around here. Not kept by the people they're referencing.
All my stuff is posted on Inmate Asylum, my systems, etc. And Ty, if you have hung around here for several years, I've very openly discussed my DIY audio projects and ideas.Prior amps of mine were pictured in 1984 (?) in Sound Practices magazine, a very nice P-P A1 Type 250 amp and a complex P-P A1 6B4G amp. A triode line stage schematic of mine, at 600 ohms, was also published by Joe Roberts.
The same has not yet been said for "whoever" Triode_Kingdom is. He is an unknown, except that he can spell, access the Forum, and post nasty thoughts up here.
So, if he wants to on-Forum attack Jeff's every post, its fair for ME to ask him to post his audio credentials. I have earned mine over 40 active years in the hi fidelity hobby Ty. He has not come forth with his..... and he won't.
I think you missed it. Those credentials are those you claim. They are not what I defined as legit. I suggest you re-read how I defined them.If you have made some breakthrough, I am sure it would spread much faster if you didn't get in the way of people who are trying to discuss it. It doesn't matter much if they're speaking positively or negatively. If you have indeed discovered something, get out of the way, it will spread if it is real. It also helps if the effect can be quantified, adjusted and explained.
Judging the response to your descriptions, I don't think you're getting very far. You may even go backwards.
Ty,There ARE people who implemented the low HY, C, DCR supply idea of Dennis'.... which I made public on Forum in 2006, and have reported positive,....actually, very positive results on Forum.
As for "lately", I just posted this information on 10 gauge / 30 gauge internal bi-wiring last week.
Give it some time, and DIYers will no-doubt, implement it, some will. It certainly is very demonstratable as the basic technique exists - optimized in all the Serious Stereo components, and, at a lower level due to my budgeting constraints, in my modded Eico HF81. I have the piece available for others to compare it - to a stock unit.
There's no 'but' that's going to work here. You've presented the idea, now get the hell out of the discussion unless somebody calls you back into it. Then get the hell back out of it afterwards.Or do you enjoy this counterproductive arguements that crop up everytime you share your most recent revelation?
Hi Jeff, I have two parallel singled ended amplifiers (pair) that are the same exept they have one difference. One has a choke input filter in the power supply. Lundahl iron in both. They sound very different. Of course one is much bigger than the other. T Willman
Why does an over speced power transformer usually sound better? Why do we hear differences in rectifier tubes? Why is the first cap/inductor in a multiple stage filter audible?Bottom line, we know we hear differences on levels that can't be defended with "science". Best we strive to keep an open mind and not censor too much which only adds to the number of posts.
"Best we strive to keep an open mind and not censor too much which only adds to the number of posts."Do you realize what you just said? :)
Anyway, I was only talking about voltage sag,nothing more.
You may not have noticed but I did include the qualifier "within reason". Obviously, if your power tranny is struggling to cope with the load, or your rectifiers are adding HF noise, or you use inadequate filtering, then you need to do something to improve things that a decent reservoir cap alone will not fix.
Well, I'd like to thing I do so let's assume I was misunderstood:)My intent was that given that we do hear things that can't be easily explained I see little point in large numbers of posts refuting what Jeff claims to hear. It is only wasted bandwith IMHO. One could make an informed guess, in an attempt to explain, but really it isn't possible to know why Jeff hears what he does. The larger gauge wiring may, or may not, have anything to do with matters.
To Jeff; I'd say you would do well to build two very simple identical amps. Nothing too fancy but using known decent stuff....say 6sn7 voltage amp DC coupled to split load invertor cap coupled to el84/6v6 triode strapped. Everything class a1 with no global feedback. Wire one amp with small gauge solid silver sleeved in cotton or teflon and the other in huge gauge PVC insulated copper. See what you think. IMHO that eico has too many things in the way to use it as a testbed to evaluate.
Any good leads for litz wire on the cheap?
...$0.15/ft: 20ft min. This is intended for RF/IF apps and is not of huge gauge. The radio grade stuff is avail elswhere too as a search using your favorite search engine will prove.
Hi Russ!!,Leads for Litz wire on the cheap??!..... Russ, I don't know what to tell you.
I was sent some old Monster / Brisson speaker wire, multi stranded, shallow angles, but it was slightly corroded internally and I did not care for it. The Monster wire was paralleled BTW, with 30 gauge CCC magnet wire. Next I tried expensive 12 gauge stranded pure silver wire - with the same 30 gauge continuous cast copper magnet wire in parallel. After break in, I liked the silver 12 gauge, until one day I paralleled some clip leads across it, went back and forth with and without the clip leads added, on the same cuts at the same volume level, and decided even more wire (than my particular silver 12 gauge) was needed to keep fully-intact the music's dynamic expressions.
In my most recent attempt, I've used Fulton Brown speaker wire, which is about a 10 gauge, multi strand, plated copper with shallow angles and tight bundling, and the same 30 gauge CCC magnet wire in paralllel.
THAT particular 10 gauge / 30 gauge combo was way-cool, 'gave me uncompressed dynamic experession on musical peaks, such as struck piano notes, etc, along with other nice cues relating to my speaker's dynamic resolution ...on ALL sorts of musical material.
I was listening to an early JBL D123 on an open baffle, with NO crossover components between the amp's output and the speaker's voice coil, and so, at 98 dB efficiency, I was able to "hear it all" very easily. The D-123 EXCELLS in transient response BTW, especially if you have good equipment powering it that does likewise.
No Russ, I don't have two of the same amplifier units to go back and forth with. But with the clip leads, EASILY added or subtracted to the existing B+ distribution wire, it allowed me to go back and forth in a controlled manner and listen to the effect of additional wire in key places. I really do trust what I heard Russ. It wasn't ever close, one way versus the other.
It was surprising to me - how much of a difference was made on my Rk self-bias resistor on the 6BQ5 output stage, when I replaced the Rk's solid wire leads with three ( and then four ) strands of Kimber TCSS. Of course, much of the amp's other wiring points was already optimized, so I could easily find the remaining weak points in wiring execution.
"They" always say, "keep the Rk self-bias resistor wiring on the output stage's ground return short", and NOW, I say, ALSO use about three or four runs of TCSS, right off the R's body, to conduct the audio signal wide-band and without information loss to ground.
As previously mentioned, I may build a 2 stage Loftin-White style DC coupled P-P amp in my old ARC D-75 chassis, using all these newer techniques. A single 6SL7 DCed into P-P 2A3s, two 5U4GB rectifiers and four 10 ohm low HY power supply Ls. The Fulton Brown speaker wire is no longer available. Dennis Fraker routinely uses expensive Siltec Silver inside his S.E. amps and attenuators, and discusses wire gauge and type, on his new Serious Stereo web site, go see that Russ.
Regards.
Jeff Medwin
> ...It was surprising to me - how much of a difference was made on my Rk self-bias resistor on the 6BQ5 output stage, when I replaced the Rk's solid wire leads with three ( and then four ) strands of Kimber TCSS....
This post is unbelievably bogus . There is not one crumb of real analytical evidence to support the claims being made here for this treatment of amplifiers. This is just snobbish, elitist BS taken to the extreme.
To nastily criticise me? This is the fourth time I've asked - and you do not answer.Tell us all YOUR audio credentials, so we can make some sense of the "reviewer" of my every post.
What sorts of systems do you have and have had in the past? How many years have you spent heavily into hi fidelity, and notice I said high fidelity, NOT electrical engineering. What sort of music collection do you have at home? When was the last time you heard live unamplified music??
What is your adjenda, mine is to further the audio art.
"Scientific proof" is not a prerequisite for posting up here Bubbah.
> "Scientific proof" is not a prerequisite for postingBut it certainly is a prerequisite to credibility, particularly when one makes these sorts of outlandish statements. Your time would be better spent demonstrating that someone besides you can hear these lightyear improvements. Until then, you can expect the community to continue to take you to task for this snobbery. And make no mistake, it IS snobbery.
regardless of the doctors 'bedside manor',i know for a fact , that he can, Hear.
take what he says, (what anyone says),
with a grain of salt.
Ah, I just said above that I heard it. Go back and read that please.
Very nicely said Russ. I'm proud of your classy post !!
Every time someone posts something that fits your view. Its pathetic.
This post is made possible by the generous support of people like you and our sponsors: