RE: Works for Me! But is it Wrong?

Posted by TubeBuilder on February 4, 2012 at 23:54:48

In Reply to: RE: Works for Me! But is it Wrong? posted by djk on February 4, 2012 at 22:43:29:

Romy was using similar values with his t350's . He was padding with the cap sise. Searching for his posts could be useful. I think it is a matter of padding down also I am guessing you are working on 8 ohm calculations which your tweeter may not be anywhere near at the given frequency. I love my auto formers that I bought from mass mutter of ebay. But I am sure you could have them wound locally. That ensures a even impedance to the amp I think. Which is really handy with 0 feedback amps. I suspect your tweeter then is less likely you change pitch with frequency but they might cause phase shifts. I linked the guy but he hasn't any listed currently. They where about $200 intact audio has some cool ones too which I am sure you know about. Auto formers make a lot of sense.

This post is made possible by the generous support of people like you and our sponsors:

Follow Ups Full Thread

Topic - I Need Your Help With A Crossover Problem - thetubeguy1954 14:51:22 02/03/12 (18)

Works for Me! But is it Wrong? - Gerry E. 10:29:29 02/04/12 (10)

RE: Works for Me! But is it Wrong? - Paul Eizik 13:18:45 02/05/12 (0)

RE: Works for Me! But is it Wrong? - djk 22:43:29 02/04/12 (8)

FE208ES-R & T900a Specifications - thetubeguy1954 03:34:57 02/06/12 (3)

RE: FE208ES-R & T900a Specifications - rbanta 17:34:09 04/20/14 (0)

RE: FE208ES-R & T900a Specifications - Paul Eizik 09:55:19 02/07/12 (1)

RE: FE208ES-R & T900a Specifications - green heron 07:52:32 04/24/14 (0)

RE: Works for Me! But is it Wrong? - TubeBuilder 23:54:48 02/04/12 (3)

RE: Works for Me! But is it Wrong? - djk 02:28:46 02/05/12 (2)

RE: Works for Me! But is it Wrong? - TubeBuilder 03:13:42 02/05/12 (1)

RE: Works for Me! But is it Wrong? - djk 05:02:16 02/05/12 (0)

RE: I Need Your Help With A Crossover Problem - Duke 17:56:59 02/03/12 (0)

RE: I Need Your Help With A Crossover Problem - Paul Eizik 16:53:00 02/03/12 (3)

RE: I Need Your Help With A Crossover Problem - thetubeguy1954 09:15:50 02/04/12 (0)

Crossover - Kloss 05:22:36 02/04/12 (1)

RE: Crossover - Paul Eizik 09:47:22 02/04/12 (0)

Mundorf MSG1 1.00uf 1200 - Kloss 14:59:02 02/03/12 (1)

RE: Mundorf MSG1--1.00uf 1200v - thetubeguy1954 09:45:09 02/04/12 (0)

Follow Ups

RE: Works for Me! But is it Wrong? - TubeBuilder 23:54:48 02/04/12 (3)

RE: Works for Me! But is it Wrong? - djk 02:28:46 02/05/12 (2)

RE: Works for Me! But is it Wrong? - TubeBuilder 03:13:42 02/05/12 (1)

RE: Works for Me! But is it Wrong? - djk 05:02:16 02/05/12 (0)

RE: Works for Me! But is it Wrong?

Post a Message!