RE: 3.7's vs MG20

RE: 3.7's vs MG20

69.237.159.70

Posted by nooshinjohn on September 9, 2012 at 08:23:16

In Reply to: RE: 3.7's vs MG20 posted by josh358 on September 9, 2012 at 06:39:42:

"That's good to know. I know that someone successfully repaired a 1-D tweeter, which also uses the dual magnet assembly."

I used mylar side of the driver as a jig for re-aligning the two halves by replacing the rivets with bolts of exactly the same diameter. This allowed me to separate the plates while not allowing them to contact one another. When putting them back together, I bolted things down tight and then replaced each bolt with a new rivet. For dis-assembly and re-assembly it took nearly a full day, and repairs to the delaminated wirs took almost a week. No wonder that Magnepan would option for replacement ove repair as it is an extensive and time consuming job, but it is actually quite easy to do. If you can handle delam repairs on other Maggies, repairs to these is not above your skill set.

This post is made possible by the generous support of people like you and our sponsors:

Follow Ups Full Thread

Topic - 3.7's vs MG20 - vectoreclectic 13:37:41 09/05/12 (29)

RE: 3.7's vs MG20 - Scottson 20:40:58 09/16/12 (1)

RE: 3.7's vs MG20 - josh358 09:48:48 09/17/12 (0)

RE: 3.7's vs MG20 - macmagman 09:27:43 09/08/12 (0)

RE: 3.7's vs MG20 - JLindborg 14:47:57 09/06/12 (0)

RE: 3.7's vs MG20 - josh358 06:20:36 09/06/12 (22)

RE: 3.7's vs MG20 - Norman M 08:23:46 09/06/12 (21)

RE: 3.7's vs MG20 - hella356 08:47:32 09/08/12 (0)

RE: 3.7's vs MG20 - Bardo 22:02:05 09/07/12 (0)

RE: 3.7's vs MG20 - patmacav 17:37:15 09/07/12 (0)

Grammar police are So anal. just sayin' LOL nt - Elizabeth 15:06:33 09/07/12 (0)

Haha thank's for a good laugh* - uncle mag 16:25:47 09/06/12 (6)

The problem being - josh358 06:10:23 09/07/12 (5)

RE: The problem being - uncle mag 15:42:59 09/07/12 (4)

RE: The problem being - josh358 18:20:03 09/07/12 (3)

RE: The problem being - uncle mag 15:54:47 09/08/12 (2)

RE: The problem being - josh358 06:27:25 09/09/12 (1)

RE: The problem being - uncle mag 20:37:57 09/10/12 (0)

RE: 3.7's vs MG20 - josh358 08:58:14 09/06/12 (9)

RE: 3.7's vs MG20 - Norman M 14:43:39 09/06/12 (8)

RE: 3.7's vs MG20 - josh358 19:09:08 09/06/12 (7)

RE: 3.7's vs MG20 - D Domaster 22:47:18 09/06/12 (6)

RE: 3.7's vs MG20 - josh358 06:18:39 09/07/12 (4)

RE: 3.7's vs MG20 - nooshinjohn 08:58:30 09/08/12 (3)

RE: 3.7's vs MG20 - josh358 06:39:42 09/09/12 (2)

RE: 3.7's vs MG20 - nooshinjohn 08:23:16 09/09/12 (1)

RE: 3.7's vs MG20 - josh358 08:32:40 09/09/12 (0)

RE: 3.7's vs MG20 - Roger Gustavsson 23:33:57 09/06/12 (0)

MG20's could be 15 years old - fin1bxn@msn.com 05:49:31 09/06/12 (0)

RE: 3.7's vs MG20 - Roger Gustavsson 23:16:31 09/05/12 (0)

Follow Ups

RE: 3.7's vs MG20 - nooshinjohn 08:23:16 09/09/12 (1)

RE: 3.7's vs MG20 - josh358 08:32:40 09/09/12 (0)

69.237.159.70

Post a Message!