Vinyl Asylum

Welcome Licorice Pizza (LP) lovers! Setup guides and Vinyl FAQ.

Return to Vinyl Asylum


Message Sort: Post Order or Asylum Reverse Threaded

TTW Audio (TTWeights) is re-opening

98.155.29.226

Posted on January 11, 2022 at 11:48:16
xsb7244
Audiophile

Posts: 371
Location: Hawaii
Joined: May 17, 2011
TTW Audio is back. And Larry Denham does vinyl.

 

Hide full thread outline!
    ...
RE: TTW Audio (TTWeights) is re-opening, posted on January 11, 2022 at 16:59:37
Not Yet There
Audiophile

Posts: 531
Joined: April 8, 2006
Considering how TTW left the industry, why would audiophiles give them a second chance?

 

You can buy their $40k turntable using paypal. That's convenient (nt), posted on January 11, 2022 at 19:22:01
Posts: 2091
Location: Orange Co., Ca
Joined: September 19, 2001
nt

 

RE: TTW Audio- I never knew they opened the first time..........., posted on January 11, 2022 at 23:38:16
beach cruiser
Audiophile

Posts: 5372
Location: so cal
Joined: September 24, 2003
Now I am only curious about how they left the industry, but it is pretty clear why they are back.

Apparently there are guys out there who will pay $200 bucks for a lathe turned and polished piece of bar-stock with one or two O rings included in the deal.

If the product is of as high quality as the photographs of the product, I think the guy is onto something.

What he is onto, I am not quite sure, because I never much liked the idea of adding weight to a bearing designed primarily to be low friction.

because that minuscule binding creates noise, one would think that adding weight , while it does alter the frequency spectrum , hopefully as intended, is counter productive to less friction and might increase noise and perhaps increase bearing wear. Almost like the automobile repair products in a can that help the problem today, like stopping a water leak, but clog the effective heat transfer, in time destroying system performance.

Consider a design that benefits from adding 24 oz. on the record surface, right by the spindle. Is it a cost limited design where they couldn't afford to add needed mass that would have improved the sound? If so, wouldn't a consumer do better with spending the additional money required for a weight into a table with a little more spent on the product that might not require additional investment. Perhaps finding a designer who realized his design goals more adeptly.

And the same goes for tables built to higher price points, if you have a need for additional aftermarket spindle weights, you have screwed up.

Of course, we are all adults here, we can say it, this is really just audio jewelry, nobody really needs it, for the reasons I pounded on above, but everyone wants to be special, and some have the ability to buy merchandise that makes their turntable look special, and sound better.

the wonderful thing is that , if one thinks a weight improves the sound, It does". Of course, that doesn't stop guys like me from kicking the carpet over in the corner of the room and muttering about yeah well what about bearing wear and the illusion of hearing, djaever think about that I would never ......, and then I wonder off to get some punch.

 

RE: TTW Audio (TTWeights) is re-opening, posted on January 12, 2022 at 03:37:58
DDzStereo
Audiophile

Posts: 132
Location: North of Toronto, Ontario
Joined: July 1, 2009
There certainly are mixed feelings and experiences about how TTW left the audio business.

The products, however, are machined to a very high standard (Jewellery? Perhaps). I have one one the periphery rims and spindle weights for my VPI rather than the similar VPI products. Do the sound better than the similar VPI products? I don't know.

I have been to the shop, very impressive, the primary business was aerospace and defence products, audio a sideline.

Never tried one of the turntables.

 

RE: TTW Audio (TTWeights) is re-opening, posted on January 14, 2022 at 06:45:22
gadio4533
Audiophile

Posts: 377
Location: FL
Joined: May 28, 2007
Recently purchased the B1000 stabilizer from them. Impressive craftsmanship, and at under $100 worth it to me.

 

+1. Adding weight to a bearing that was never designed to handle it., posted on January 15, 2022 at 08:41:06
Mick Wolfe
Audiophile

Posts: 2870
Joined: October 10, 1999
Contributor
  Since:
September 4, 2000
NT

 

Page processed in 0.032 seconds.