|
Audio Asylum Thread Printer Get a view of an entire thread on one page |
For Sale Ads |
76.90.39.24
In Reply to: RE:Actually, i had a circuit problem. But, your suggestion is good posted by DAK on January 07, 2017 at 14:39:33
If your circuit uses fixed bias why do you have a cathode resistor.
With the grid resistor feed by a negative bias supply the cathode should just be grounded.
BTW I read your other post and if you are going to use a LED in the cathode for cathode biasing you still need a proper amount of plate current and a proper amount of plate voltage.
You want to operate the tube somewhere that the tube is linear.
A 6sn7 with only 60 volts on the plate and only 2ma. (or so) is not a linear place.
___
I like 12-14ma 200 volts on the plate but that operating point is out of the question it you use a plate resistor.
I use a CCS plate load.
It makes everything easier and makes for a very linear stage with a lot of plate voltage swing (if you need a lot of swing, like in a driver stage).
Tre'
Have Fun and Enjoy the Music
"Still Working the Problem"
Follow Ups:
for the driver tube. I know i can get a B+ of 300v for the driver stage.
As it stands now, i have 2 LEDs in series, which puts the 7a4 cathode at 3V. This also raised the Plate voltage to 115vdc.
I got some SS devices although i am not sure if they are rated for hi voltage. The ones i have are LR8N3G, TIP50, LM337, LM317HT. Can i make a CCS for the 7A4 plate with any of those. regards, Dak
Edits: 01/07/17 01/07/17
Something is not adding up here.
If you look at the plate curves for a 7a4 at the spot where 115 volts plate and -3 volts bias intersect. That shows about 4.5ma. plate current.
4.5ma of current across 80k ohms will drop 360 volts.
To end up with 115 volts at the plate you would have to start with a 475 volt supply feeding the top of the plate resistor.
As for CCS......DN2540 are cheap. $1.42 each at Mouser.
Check the link below.
Tre'
Have Fun and Enjoy the Music
"Still Working the Problem"
The plate resistor is now 50K. I am thinking of adding another LED. That should bring the voltage up to a good point. Thank you for the link i will definitely check that out. cheers, Dak
Edits: 01/08/17
"The plate resistor is now 50K"
Ok, now things make more sense.
"I am thinking of adding another LED"
That will drive the current even lower.
The plate voltage will be higher, like you said, but I don't think the tube will be very linear at such a low current.
Tre'
Have Fun and Enjoy the Music
"Still Working the Problem"
Hi Tre, with 3 LEDs the voltages are now; Av 168. Kv 5.57vdc. and the plate resistor is actually 56k. The B+ to the plate resistor is 360 under the conditions set by the 3 Leds.
Ok, those numbers all line up like they should.
With a 56k ohm plate load the load line will be pretty horizontal but with only 3.4ma of plate current that tube will not be as linear as it would be if there was more current.
More current with a 56k ohm plate resistor would take a lot of B+ (supply) voltage.
A CCS will give you your cake (a horizontal load line) and you can eat it to (get about 10 or more ma. of current going).
Then that tube would be very linear (low distortion).
Just something to think about.
Tre'
Have Fun and Enjoy the Music
"Still Working the Problem"
In this situation, with my new amp, i would like to keep the variables as few as possible, so i would rather get one that has seen a lot of people using them and so would be vetted and less worrisome? In other words if i build one i still would not be sure if i had an poor interaction between the CCS and my amp. So, i would rather buy one with a good "track history" as it were.
K&K Audio (here on the AA) sells kits.
Look for "Two Terminal Constant Current Source" on the page linked below.
You want the Cascode ones (2 MosFets per CCS).
I just make my own using a pair of the dn2540 MosFets.
All it takes is 2 of the MosFets, 2 gate stop resistors and a current set resistor. That's it!
Tre'
Have Fun and Enjoy the Music
"Still Working the Problem"
Right, Kevin sells them. i will check that out. But later, do you mind if i contact you about building my own? thanx for the link. regards
Just send email through the AA.
I'll help.
Tre'
Have Fun and Enjoy the Music
"Still Working the Problem"
Post a Followup:
FAQ |
Post a Message! |
Forgot Password? |
|
||||||||||||||
|
This post is made possible by the generous support of people like you and our sponsors: