Small Boat Forum

Welcome! Need support, you got it. Or share you ideas and experiences.

Use this form to submit comments directly to the Asylum moderators for this forum. We're particularly interested in truly outstanding posts that might be added to our FAQs.
You may also use this form to provide feedback or to call attention to messages that may be in violation of our content rules.

You must login to use this feature.

Inmate Login

By default, logging in will set a session cookie that disappears when you close your browser. Clicking on the 'Remember my Moniker & Password' below will cause a permanent 'Login Cookie' to be set.

Moniker/Username: The Name that you picked or by default, your email. Forgot Moniker?	Examples "Rapper", "Bob W", "joe@aol.com".
Password:	Forgot Password?
	Remember my Moniker & Password ( What's this?)

If you don't have an Asylum Account, you can create one by clicking Here.

Our privacy policy can be reviewed by clicking Here.

Inmate Comments

From:
Your Email:
Subject:

Message Comments

Original Message

Re: Small Boat Suggestions

Posted by Chief on April 7, 2004 at 00:40:36:
Build you one. A wooden boat is Great. For anything heavy like a wide long boat I would use 3/8 ext ply. I would think 14 feet long 4 or 5 feet wide would be plenty. The flat bottom type are easy to build. Some people think they need a v bottom forward but, when the boat planes it runs on the flat bottom aft anyway. Make the sides atleast 16 inches deep and the transom 16 inches deep or cut a notch for the motor unless you have a long foot. Long motors need 20 inch transoms and short need 16 inches max depth transoms. IF the transom slopes at all it must be longer than sides are deep to match the angle of the slope. You can make the sides deep as you like as long as the motor foot reaches deep enough into the water. Slope the sides outward slightly IF you intend to be in rough water and use a motor strong enough to get you on plane. I like to plane on dangerous water. It beats boggin down in the waves. I would consideer making my sides square if I were using a 5 hp engine or less on a boat 48 inches wide with 16 inch deep sides 14 feet long. A good 9.5 will do the trick well. NOT to fast but fast enough to scare me. Square sides and a scow bow are a little bit easier to build. Go to msn groups.smallboats and take a look at the Q&E#2. That is only 8 feet long and 32 inches wide. It is a scow but the aft end could be built with a LOT less angle and a motor could be used. A boat like that is easy to build. If you will be in really rough water your boat could be 6 or 7 feet wide. Use a big enough motor to get it on plane but NOT real fast and be careful in the turns and you got a nice boat. I have noticed that square of boxy boats tend to be a little rubbery. You know, they have some flex, twist like a shoe box. The end decks on my scow and side decks on a big boat would take care of that. Boats that taper in at the front and aft tend to be more rigid. I am in the process of desiging a boat 7 or 8 feet wide, 24 inches deep, and 16 feet long. Have not yet decided IF It will have sloping sides or not. I have seen a boat called a Brick that does well with square sides. Look at the Shanty boats. Most have square sides. Sloping sides may help the boat to jump up when a wave hits it from the sides and I am told they help the boat NOT flip over in a fast tight turn. The boat I am desiging will be easy to build and I can give you the plans for free IF you want a boat that big. I like big. I have small and I like small also but for big waters, swift, or rough choppy waters, I like big. I intend to use my big boat on Red River and for camping and night fishing. It will take 7-9 sheets of ply to build. The ply is gone sky high so I may wait another year before building it.