yes I'm sure its to scale - Ernie L

Vinyl Asylum

Welcome Licorice Pizza (LP) lovers! Setup guides and Vinyl FAQ.

Follow Ups Full Thread

Topic - which method or does it matter? - Ernie L 13:55:49 07/12/06 (29)

survey says...Baerwald !..thanks all* - Ernie L 16:38:38 07/12/06 (0)

some printers will - kavakidd 16:02:32 07/12/06 (1)

yes I'm sure its to scale - Ernie L 16:45:30 07/12/06 (0)

Re: which method or does it matter? - John Elison 15:52:50 07/12/06 (14)

Actually Loefgren developed them in 1938, Baerwald "signed on" later. - Garth 20:41:04 07/12/06 (0)

Uh, the early 1040s??? Say what? /nt\ - HenryH 16:35:29 07/12/06 (6)

I meant 1940s. Sorry! (nt) - John Elison 05:03:48 07/13/06 (4)

Actually 1941, released just before Pearl Harbor. - Garth 07:48:28 07/13/06 (3)

Re: Actually 1941, released just before Pearl Harbor. - John Elison 12:27:56 07/13/06 (2)

Yes, that is unfortunately true. - Garth 12:37:32 07/13/06 (1)

Re: Yes, that is unfortunately true. - John Elison 13:51:36 07/13/06 (0)

He was like Leo da Vinci. WAY ahead of his time. nm - tketcham 17:55:47 07/12/06 (0)

Re: which method or does it matter? - Borough33 16:35:22 07/12/06 (5)

Re: which method or does it matter? - John Elison 06:20:12 07/13/06 (1)

Very helpful, thanks. (nt) - Borough33 08:00:32 07/13/06 (0)

If you can measure 0.11 mm then go for it. nm - tketcham 17:53:51 07/12/06 (2)

That wasn't very courteous. So here's a more civil response... - tketcham 22:04:25 07/12/06 (1)

Right, and it's actually 66.04mm. (-: (nt) - Garth 23:54:16 07/12/06 (0)

Baerwald /nt - Nasty 15:25:37 07/12/06 (0)

Two different alignment methods, that's all. - olddude55 15:11:51 07/12/06 (5)

well I could always print out the Loefgren scale - Ernie L 15:17:48 07/12/06 (4)

I think the TT Basics is Baerwald... - olddude55 15:26:08 07/12/06 (3)

TT Basics is Baerwald. You are correct. (nt) - John Elison 15:31:41 07/12/06 (2)

Hah! Doesn't happen too damned often! nt - olddude55 15:39:54 07/12/06 (1)

Hey, Olddude; it happens enough. Wait until I go to Seattle. ;-) (nt) - John Elison 15:58:11 07/12/06 (0)

Just an idea... - FrankieLuvsVinyl 14:44:40 07/12/06 (3)

there is a scale in mm on it just to check for that..thanks* - Ernie L 14:55:15 07/12/06 (2)

The best thing to check is the distance from the spindle-hole to the null-points.... - John Elison 15:29:40 07/12/06 (1)

Thanks........... I'll double check it * - Ernie L 16:57:42 07/12/06 (0)

Follow Ups

yes I'm sure its to scale - Ernie L 16:45:30 07/12/06 (0)