Vinyl Asylum Welcome Licorice Pizza (LP) lovers! Setup guides and Vinyl FAQ. |
|
Haven't posted for ages but wanted to share my new project!
On the right is my 'original' AR The Turntable... But with all the moving parts replaced. Merrill PolyChassis/ platter and motor. Rega/Mitchell arm.
In front is my newly built plinth with all the original AR parts. Spinning Starker Bach Cello and its sounding nice.
This post is made possible by the generous support of people like you and our sponsors:
Topic - My new AR clone - Pivo 17:09:55 11/18/20 (28)
- RE: My new AR clone - B.K. 19:35:31 11/19/20 (0)
- RE: My new AR clone - rwiley 14:14:08 11/19/20 (0)
- Verah nizzze. - ghost of olddude55 14:09:26 11/19/20 (0)
- Sweet ! ... - reelsmith. 12:55:48 11/19/20 (1)
- Ditto. nt - Rick W 14:05:48 11/19/20 (0)
- RE: My new AR clone - Logan 22:44:11 11/18/20 (7)
- Felt mat? - M3 lover 09:36:54 11/19/20 (2)
- My AR-XA came with a foam mat. - alaskahiatt 21:48:32 11/20/20 (0)
- RE: Felt mat? - Pivo 14:44:13 11/19/20 (0)
- Question on the mat - Story 07:07:46 11/19/20 (3)
- Very good. I notice no clinging or static discharge with the herbies mat on my SL-1500C. /nt\ - Opus 33 1/3 11:49:07 11/19/20 (2)
- I get a little bit of static cling, but the Herbie's is heavy enough that it doesn't matter. nt - ghost of olddude55 14:57:24 11/20/20 (0)
- Ok many thanks! - Story 12:49:12 11/19/20 (0)
- RE: My new AR clone - B. Scarpia 19:11:05 11/18/20 (6)
- RE: My new AR clone - Pivo 14:50:24 11/19/20 (5)
- RE: I unwisely tried to stretch this project into my pre-op pass the drugs I can't stand the farging pain phase - B. Scarpia 16:38:14 11/19/20 (4)
- The angle join on the top one is not as nest as the others. )MT( - J. S. Bach 06:22:35 11/20/20 (3)
- RE: That's why god created the #4 Smoothing Plane with cambered blade ;-) - B. Scarpia 06:36:23 11/20/20 (2)
- RE: That's why god created the #4 Smoothing Plane with cambered blade ;-) - B. Scarpia 16:57:17 11/20/20 (0)
- "One of these is not like the others. Can you tell which one?" I was referring to that statement in your... - J. S. Bach 16:37:53 11/20/20 (0)
- RE: My new AR clone - John-from Seattle 18:43:57 11/18/20 (1)
- RE: My new AR clone - Pivo 04:35:46 11/19/20 (0)
- Beautiful workmanship! - John Elison 18:06:01 11/18/20 (1)
- RE: Beautiful workmanship! - Pivo 18:34:59 11/18/20 (0)
- Very beautiful work - of course, I'm hoping that. . . - Chris from Lafayette 17:24:05 11/18/20 (2)
- RE: Very beautiful work - of course, I'm hoping that. . . - Pivo 17:42:04 11/18/20 (1)
- Not to mention the even later recording on RCA/BMG - Chris from Lafayette 00:50:16 11/19/20 (0)
- RE: My new AR clone - Sondek 17:18:56 11/18/20 (0)