RE: Yep...

Tubes Asylum

Questions about tubes and gear that glows. FAQ

Follow Ups Full Thread

Topic - My 300B tubes don't fit - Will G. 17:54:37 03/07/21 (35)

RE: My 300B tubes don't fit - Will G. 19:03:13 03/11/21 (7)

RE: My 300B tubes don't fit - Will G. 19:10:44 03/11/21 (6)

RE: My 300B tubes don't fit - Tre' 19:27:44 03/11/21 (5)

Yep... - Ivan303 19:37:12 03/11/21 (4)

Philips capacitors? - maxhifi 06:01:57 03/12/21 (1)

Strange chinese manufactures printed something "audiophile" on a shrink wrap? (nr) - Chip647 20:46:34 03/16/21 (0)

RE: Yep... - Tre' 20:04:57 03/11/21 (1)

RE: Yep... - Triode_Kingdom 22:22:27 03/11/21 (0)

Did you take the bottom off your preamp to see what was in the way of the tube pins? nt - Tre' 16:39:32 03/11/21 (0)

something really wrong here - Story 06:10:58 03/10/21 (0)

What brand is it? - Ivan303 05:34:59 03/10/21 (0)

Avoid that manufacturer like the plague - Jay Buridan 09:31:49 03/09/21 (8)

Which one?? - Ralph 10:10:49 03/10/21 (7)

Sorry. PS Vane - Jay Buridan 05:36:37 03/17/21 (0)

Guessing that it's a problem with the tube socket... - Ivan303 14:42:49 03/10/21 (5)

RE: Taks a look at Tre's photo in the subthread below - Ralph 14:57:00 03/10/21 (4)

Didn't see any mention by the OP as to the brand of amp.... - Ivan303 15:50:40 03/10/21 (3)

In a post below.. - Tre' 17:51:37 03/10/21 (2)

Ah yes, different post. - Ivan303 18:54:33 03/10/21 (1)

RE: Ah yes, different post. - Tre' 19:37:03 03/10/21 (0)

Blue resistors under the tube sockets. - Tre' 08:28:43 03/09/21 (1)

RE: Blue resistors under the tube sockets. - zacster 07:58:06 03/10/21 (0)

Check your tubes against this drawing from the WE Data - maxhifi 07:44:29 03/09/21 (1)

Ah. Good point! - Jonesy 14:08:16 03/10/21 (0)

RE: My 300B tubes don't fit - Will G. 17:06:47 03/08/21 (0)

RE: My 300B tubes don't fit - Blackdog 13:50:15 03/08/21 (3)

RE: My 300B tubes don't fit - Triode_Kingdom 15:27:44 03/08/21 (2)

'Mute' button while Rod is at it... - Ivan303 07:00:30 03/10/21 (0)

TK, I do the same thing. nt - Tre' 08:19:10 03/09/21 (0)

Do not file off the bottom of the tubes. That is a really bad idea. nt - Tre' 06:10:22 03/08/21 (0)

Spacer - RedM 05:14:52 03/08/21 (1)

RE: Spacer - Rocket_Powered 06:35:19 03/08/21 (0)

Change the tube socket! - andy evans 00:57:52 03/08/21 (1)

Clearly there must be a 'bottom' on the tube socket pin holes.... - Ivan303 08:34:34 03/08/21 (0)

RE: My 300B tubes don't fit - Sherlock 19:47:41 03/07/21 (0)

Follow Ups

RE: Yep... - Triode_Kingdom 22:22:27 03/11/21 (0)

Post a Message!