In Reply to: RE: measurements ... posted by rage on May 11, 2015 at 09:07:29:
The 6SN7 was too lazy, not enough gain or jump factor in my multi-amp set up for good level matching.I set up 6SL7 C4S but got horrid distortion until I realized that I needed at least 2mA bias current for the extended C4S to work properly.
THD = 1.24% at 1W with 1KHz sine input.
Overall gain = 2.5
I realized an improvement of about 1% THD vs. 6SN7/triode 6V6 active parafeed circuit at the same 1W power output.
Not sure that JM or DF will approve of your pentode driver for 2A3.
DT667
Edits: 05/11/15
This post is made possible by the generous support of people like you and our sponsors:
Follow Ups
- RE: 6SL7 C4S driver ... - deathtube 667 17:50:45 05/11/15 (22)
- RE: 6SL7 C4S driver ... - Tre' 19:54:23 05/11/15 (21)
- RE: 6SL7 C4S driver ... - Al Noakes 06:37:03 05/13/15 (16)
- RE: 6SL7 C4S driver ... - drlowmu 09:57:05 05/13/15 (15)
- RE: 6SL7 C4S driver ... - Al Noakes 10:34:05 05/13/15 (14)
- RE: 6SL7 C4S driver ... - Triode_Kingdom 11:12:08 05/15/15 (0)
- RE: 6SL7 C4S driver ... - Lew 10:46:35 05/15/15 (0)
- RE: 6SL7 C4S driver ... - LinuxGuru 10:56:42 05/13/15 (11)
- RE: 6SL7 C4S driver ... - Al Noakes 14:21:24 05/13/15 (10)
- RE: 6SL7 C4S driver ... - drlowmu 10:25:25 05/14/15 (1)
- RE: 6SL7 C4S driver ... - Al Noakes 23:59:35 05/14/15 (0)
- RE: 6SL7 C4S driver ... - deathtube 667 08:42:26 05/14/15 (7)
- RE: 6SL7 C4S driver ... - Al Noakes 23:55:51 05/14/15 (4)
- RE: send in the clowns ... - deathtube 667 17:06:42 05/15/15 (3)
- RE: send in the clowns ... - Al Noakes 03:27:30 05/17/15 (2)
- RE: you are correct ... - deathtube 667 08:57:04 05/17/15 (1)
- Beautiful Job !!! - drlowmu 07:21:00 06/01/15 (0)
- RE: 6SL7 C4S driver ... - rage 16:13:48 05/14/15 (1)
- RE: 6SL7 C4S driver ... - drlowmu 09:27:37 05/15/15 (0)
- RE: 6SL7 C4S driver ... - hennfarm 17:04:47 05/12/15 (0)
- RE: 6SL7 C4S driver ... - Mr_Steady 16:26:51 05/12/15 (2)
- RE: 6SL7 C4S driver ... - Tre' 19:08:32 05/12/15 (1)
- RE: 6SL7 C4S driver ... - Mr_Steady 08:32:14 05/13/15 (0)
- RE: 6SL7 C4S driver ... - deathtube 667 15:01:54 05/12/15 (0)