As predicted previously by others, I find I can not change between two amps quick enough for proper A/B testing even though I have a switch that lets me select one or the other amp to go to the same set of speakers. It still takes about 20 seconds and I have to get up from my listening position to do it and turn off one amp and turn on the other.
I would instead like to be able to leave both amps on, balance out the volume levels, and then switch amps from my listening position.
I have enough selector switches to do it, but my problem is keeping a load on the amp that is not switched in to the speakers.
I did a little searching on the net and found one suggestion to put a 150 ohm/5w resistor across the terminals of each amp so that they have a load when not switched in.
Does anyone have any experience with setting this up? Does the above method work or do you know of a better method?
Thanks
This post is made possible by the generous support of people like you and our sponsors:
Topic - A/B testing set up...... - vinnie2 05:42:04 10/23/14 (23)
- Short term A/B tester up and running..... - vinnie2 06:45:29 10/25/14 (0)
- How would this work? - vinnie2 13:20:33 10/23/14 (0)
- RE: A/B testing set up...... - SteveBrown 11:29:08 10/23/14 (0)
- RE: A/B testing set up...... - Nickel Core 11:22:10 10/23/14 (1)
- RE: A/B testing set up...... - vinnie2 12:20:57 10/23/14 (0)
- RE: A/B testing set up...... - 6AS7_6SN7 07:15:46 10/23/14 (3)
- RE: A/B testing set up...... - vinnie2 07:35:24 10/23/14 (2)
- RE: A/B testing set up...... - bcguitar 08:43:39 10/23/14 (1)
- RE: A/B testing set up...... - vinnie2 09:58:09 10/23/14 (0)
- RE: A/B testing set up...... - Thomas Mayer 05:49:11 10/23/14 (13)
- RE: A/B testing set up...... +1 - deathtube 667 03:08:41 10/24/14 (0)
- RE: A/B testing set up...... - vinnie2 06:16:06 10/23/14 (11)
- RE: A/B testing set up...... - Tre' 08:10:09 10/23/14 (10)
- RE: A/B testing set up...... - vinnie2 09:54:54 10/23/14 (9)
- RE: A/B testing set up...... - Tre' 17:02:13 10/23/14 (8)
- RE: A/B testing set up...... - vinnie2 17:36:56 10/23/14 (7)
- RE: A/B testing set up...... - Thomas Mayer 23:45:09 10/23/14 (1)
- "As soon as you switch to 'technical' listening mode, it gets very difficult" Amen to that. - Tre' 09:31:16 10/24/14 (0)
- RE: A/B testing set up...... - Tre' 17:56:51 10/23/14 (4)
- RE: A/B testing set up...... - grindstone 19:06:11 10/23/14 (0)
- RE: A/B testing set up...... - vinnie2 17:58:54 10/23/14 (2)
- RE: A/B testing set up...... - deanznz 15:03:24 10/25/14 (1)
- RE: A/B testing set up...... - vinnie2 17:52:25 10/25/14 (0)