In Reply to: Is there a reason you want to use a tube rectifier? posted by FenderLover on April 6, 2016 at 18:41:54:
I'm very sure I want to, no matter the failure potential. Everything on the bias circuit is audible and I do not want sand there.
This post is made possible by the generous support of people like you and our sponsors:
Follow Ups
- RE: Is there a reason you want to use a tube rectifier? - aknaydenov 23:25:20 04/06/16 (25)
- The goldenears at conrad-johnson must believe most of that, too... - jeffreybehr 11:28:24 04/08/16 (0)
- "Everything on the bias circuit is audible" - Chip647 05:19:13 04/07/16 (23)
- RE: "Everything on the bias circuit is audible" - aknaydenov 13:52:52 04/07/16 (22)
- RE: "Everything on the bias circuit is audible" - cpotl 17:52:23 04/07/16 (0)
- RE: "Everything on the bias circuit is audible" - Tre' 16:44:37 04/07/16 (20)
- RE: "Everything on the bias circuit is audible" - aknaydenov 23:47:45 04/07/16 (19)
- RE: "Everything on the bias circuit is audible" - cpotl 17:22:01 04/08/16 (16)
- RE: "Everything on the bias circuit is audible" - aknaydenov 05:31:57 04/09/16 (15)
- RE: "Everything on the bias circuit is audible" - Tre' 13:03:45 04/09/16 (13)
- Timbre - Tre' 14:10:48 04/09/16 (11)
- Attacks come first in importance, and then decays, and harmonics on the continuus tone come last - Timbo in Oz 17:15:17 04/12/16 (10)
- RE: Attacks come first in importance, and then decays, and harmonics on the continuus tone come last - Tre' 18:19:47 04/13/16 (2)
- The bit below the quoted article noted that this was opinion. - Timbo in Oz 22:25:17 04/13/16 (1)
- RE: The bit below the quoted article noted that this was opinion. - Tre' 11:35:31 04/14/16 (0)
- No Valve Rectifiers? - Triode_Kingdom 13:09:29 04/13/16 (6)
- two of those resistors that coe n slowly one on the primary AC feed and one on the HT secondary. - Timbo in Oz 14:41:48 04/13/16 (5)
- I don't think that's very effective - Triode_Kingdom 08:21:40 04/14/16 (0)
- What, pray tell, is 'coe n'? (NT) - jeffreybehr 18:42:18 04/13/16 (3)
- come on? Sorry - Timbo in Oz 21:27:28 04/13/16 (2)
- RE: come on? Sorry - aknaydenov 10:38:17 04/14/16 (1)
- RE: come on? Sorry - drlowmu 21:02:47 05/01/16 (0)
- As Richard C. Heyser conjectured... we know not ... yet... what to measure.~nT - Cleantimestream 13:29:44 04/09/16 (0)
- +1 - drlowmu 10:46:01 04/09/16 (0)
- What test equipment do you own or use? (nt) - gusser 11:49:43 04/08/16 (0)
- Essentially what Richard C. Heyser said.... He was embarking on why before he died-nT - Cleantimestream 08:31:29 04/08/16 (0)