RE: Altec Model 19 - N1201-8A Crossover Question

Posted by Synthsayer (A) on September 2, 2015 at 11:31:39

In Reply to: Altec Model 19 - N1201-8A Crossover Question posted by Synthsayer on August 29, 2015 at 13:41:44:

I was mistaken about the cutoff for the horn and driver; it is at 500Hz whcih is close to the lowest useable pint for the driver.

Looking at the the horn's specs again, I saw that there is an asterisk next to the freq response. The note says freq response up to 12k which explains why I don't hear cymbals and hi hats as well as I would like.

I can add a tweeter. I just have to figure out how to mount it.

I have JBL 2402 or Selenium/JBL ST200.

"Ad Astra Per Alia Porci", - To the stars on the wings of a pig: John Steinbeck

This post is made possible by the generous support of people like you and our sponsors:

Follow Ups Full Thread

Topic - Altec Model 19 - N1201-8A Crossover Question - Synthsayer 13:41:44 08/29/15 (17)

RE: Altec Model 19 - N1201-8A Crossover Question - Synthsayer 09:33:45 09/03/15 (0)

RE: Altec Model 19 - N1201-8A Crossover Question - Synthsayer 13:01:37 09/02/15 (0)

RE: Altec Model 19 - N1201-8A Crossover Question - Synthsayer 11:31:39 09/02/15 (0)

RE: Altec Model 19 - N1201-8A Crossover Question - Synthsayer 11:20:53 09/02/15 (0)

RE: Altec Model 19 - N1201-8A Crossover Question - DaveV 07:54:15 08/30/15 (12)

RE: Altec Model 19 - N1201-8A Crossover Question - Synthsayer 09:45:36 08/30/15 (11)

RE: Altec Model 19 - N1201-8A Crossover Question - Synthsayer 09:09:26 09/02/15 (1)

Altec Model 19 does not use a... - Cougar 11:22:43 09/02/15 (0)

RE: Altec Model 19 - N1201-8A Crossover Question - DaveV 13:22:42 08/30/15 (8)

RE: Altec Model 19 - N1201-8A Crossover Question - Cougar 19:15:48 09/01/15 (1)

RE: Altec Model 19 - N1201-8A Crossover Question - DaveV 19:48:12 09/01/15 (0)

RE: Altec Model 19 - N1201-8A Crossover Question - Synthsayer 13:05:16 08/31/15 (0)

RE: Altec Model 19 - N1201-8A Crossover Question - Steve O 18:05:13 08/30/15 (4)

RE: Altec Model 19 - N1201-8A Crossover Question - Synthsayer 13:04:03 08/31/15 (0)

RE: Altec Model 19 - N1201-8A Crossover Question - timoteus 19:34:55 08/30/15 (2)

RE: Altec Model 19 - N1201-8A Crossover Question - Synthsayer 13:00:08 08/31/15 (0)

RE: Altec Model 19 - N1201-8A Crossover Question - Steve O 20:08:57 08/30/15 (0)

Follow Ups

RE: Altec Model 19 - N1201-8A Crossover Question - Synthsayer 11:31:39 09/02/15 (0)

RE: Altec Model 19 - N1201-8A Crossover Question

Post a Message!