Chipset & Features:
(as delivered in standard configuration)
- Inputs - 2 RCA & BNC (switchable)
- High Grade Input Pulse Transformer
- CS8414 Digital Receiver on IC socket (CS8412 can be fitted or DIR9001 on
adapter board)- High Grade 11.2896 MHz clock Oscillator for reclocking (44.1KHz source
only)- SAA7220 Digital Filter (can be bypassed for 1X sampling) on IC socket
(can be removed)- TDA1541A DAC (single) on IC socket (can be upgraded with crown/double
crown TAD1541A)- 4 pcs OPA604 I/V conversion and lowpass filter/output buffer on IC
Sockets (upgrade with AD8610 and BUF04 or other options)- Dual RCA Outputs (CMC Brand high grade sockets)
- High grade line output transformers on output pair B
- High Grade encapsulated 50VA torroidal mains transformer (115/230V
universal worldwide primary windings)- 8,800uF power supply capacitance in high grade Nichicon Japan capacitors
- 4,000uF power supply capacitance, Nichicon Japan Muse capacitors
- 6pcs LM317T Regulator
- 3pcs LM337T Regulator
- Analog stage power supply can be adjusted from ±5V to ±18V to suit
the power supply requirements of any op-amp's used- Extensive supply decoupling using Nichicon Muse bipolar capacitors and
film bypass capacitors- Includes top quality Gotham Cable Switzerland internal analog line
output cables and silverplated copper & teflon true 75 Ohm impedance coaxial
internal digital signal CableTechnical Data
(all measured in 4X Oversampling Configuration without reclocking
and with standard analog stage and Output A (transformerless)
connected)
- Signal/Noise ratio: >95dB
- Output Voltage: > 2V RMS @ 0dbfs
- Output Impedance: < 220 Ohm
- Response: 20hz to 20k +-0.5db
- Output Polarity: Non inverting (correct polarity)
- Channel Separation: >85db
- Distortion: <0.002%
- Max Wordlength: 24Bit (DAC will accept 24 bit data, but will
convert only the 16 most significant bits)- Max Sample Rate: 96KHz with CS8414 fitted (1X operation), 48KHz
in 4X operation, 192KHz can be processed by the DAC in 1X operation if a
suitable receiver module is fitted (not supplied)- Jitter Reduction: High-stability crystal-controlled re-clocking
for all inputs (44.1KHz sample rate only)- Input Connections: 2 input connectors (RCA and BNC) selectable via
rear panel switch and D-Sub for I2S (option - not connected as
standard)- Output Connections: 2 pairs of output connectors (RCA), output
transformer on pair B or op-amp on pair A- Power Consumption: 100-135VAC or 200-270VAC 50/60hz 20W
- Dimensions: 440 (L) x 320(W)x100 (H)mm
- Weight: 10 kg (packed)
Alternative Configurations and Options
(included unless
noted otherwise)
- Operation with or without reclocking (via jumper configuration)
- Operation with 4 X oversampling digital filter or without digital filter
(via jumper configuration)- Single Op-Amp, inverting polarity output with NE5534 for experimenters
(replacement PCB, fully assembled, plug & play)- Operation with S/P-DIF direct input bypassing input switching and input
transformer for purest sound quality (requires soldering - basic)- Analog Stage Upgrade component pack (NOT INCLUDED - EXTRA COST OPTION)
for standard output stage including AD8610 operational amplifiers, BUF04
buffers, Elna Silmic output coupling capacitors and polystyrene analog
filter capacitors; basically the best of the best available (requires some
soldering - advanced)- Blank PCB for conversion to Gemini (Twin) DAC Status (requires
soldering, extra components and reconfiguration - highly advanced)- I2S input on SUB-D 9-Pin connector bypassing internal digital receiver
(requires soldering and reconfiguration and suitable source - highly
advanced)
Edits: 01/07/08 01/08/08 01/08/08 01/08/08
This post is made possible by the generous support of people like you and our sponsors:
Topic - Satch - description - bcherry 00:34:29 01/07/08 (1)
- SatchWatch Siting - bcherry 00:50:29 01/07/08 (0)