|
Audio Asylum Thread Printer Get a view of an entire thread on one page |
For Sale Ads |
209.91.107.226
In Reply to: RE: Tonearm Interface/Junction Box posted by Catastrofe on January 30, 2015 at 08:01:14
I've got a VPI arm with a junction box, but I like to swap out cartridges so it's convenient for me. If I wasn't swapping, I'd avoid that method. When comparing a straight through to male RCA configuration, It's not just one extra connection, it's six!!
In VPI's case, the tonearm wires are soldered to a Lemco connector (1) which plugs into the junction box (2). Inside the junction box is a short piece of wire soldered to the Lemco input and the RCA output (3 and 4). Your choice of external cable will be plugged into the RCA output (5) and those cables contain one more solder joint (6).
That's a lot of extra connections for a teeny tiny electrical signal to pass through.
Back in the day, the best upgrade I made to my old Kenwood was to bypass the internal wire and run 30 gauge solid core direct from headshell clips to male RCAs which plugged directly into the phono stage.
Follow Ups:
nt
Dman
Analog Junkie
> That's a lot of extra connections for a teeny tiny electrical signal to pass through.
This is a common misconception about electricity. The number of connections have no greater impact on a very low current electrical signal as on a high current signal. In other words, if there is any sort of negative effect regarding these connections, it makes no difference whatsoever whether the electrical signal is in microamperes or amperes. Furthermore, if the connections are constructed properly, they will have negligible impact on the signal.
In order to make sure electrical connections have the least impact on any electrical signals, it is important to use a contact enhancer such as Caig DeoxIT Gold on all unplugable connections. For solder connections it is important to use the best solder.
Connection points increase resistance. However, when done properly any additional resistance will be negligible. In fact, the additional resistance from running 33-gauge wire an extra meter to your preamp will probably be 100-times greater than the resistance of six additional connections done properly.
Best regards,
John Elison
My theory made sense in my head.
Thanks for bringing forth the facts John. I guess I should edumicate myself a little better on the hows and whys of electrons. :-)
an Indium based one has only 28% the resistance of copper wire. The more connections the worse it does become, simply because the solder forms an interface between the connector and the wire. No solder and after a few years that crimped interface corrodes, at least in my experience.
Sorry, reference can be found on the Indium website. The indium Corp, also makes standard type solders, SN62, etc. so you can easily make comparison.
most of the solder sold under the indium name is not made of indium :)....the ones i found are like SAC 305 or Sn63 Pb37 some with silver, mostly traditional mixes :)
dee
;-D
True terror is to wake up one morning and discover that your high school class is running the country.
quote by Kurt Vonnegut
Indium is found mixed in with lead in nature and is a bit difficult to extract. Hence the indium corp makes standard lead solder too. Their website lists conductivity of their solders. I honestly forgot the high conductivity formula, except for the fact that it was expensive. I have some somewhere but have yet to make a controlled listening test.
Also interesting to note much lower melting point. Might be good for smd stuff.
Edits: 02/01/15
sn62 conductivity 11.9%
97 In, 3Ag. 23%
100 In. 24%
These indium formulations not common at all and pricey
EBay has a pound of 97in3ag solder. Buy it now for $4950!!!!
that is probably not the source i want to use...
dee
;-D
True terror is to wake up one morning and discover that your high school class is running the country.
quote by Kurt Vonnegut
May not be really horrible : depending on how much a 3' by .03" weights
dee
;-D
True terror is to wake up one morning and discover that your high school class is running the country.
quote by Kurt Vonnegut
Great info Stu. Thanks for sharing.
Post a Followup:
FAQ |
Post a Message! |
Forgot Password? |
|
||||||||||||||
|
This post is made possible by the generous support of people like you and our sponsors: