|
Audio Asylum Thread Printer Get a view of an entire thread on one page |
For Sale Ads |
74.70.178.30
In Reply to: RE: Phoenix Engineering Falcon PSU (similar to VPI SDS) review video posted by phoenixengr on July 29, 2014 at 10:39:32
Well, I'm not here to front for VPI. If you can do the same for less money that's fine and if HW wants to he will respond for VPI.
But I must say this whole thread, beginning with the OP celebrating dials and LEDs instead of improved audio, and followed by all of your posts celebrating technology looks more like an advertisement for Phoenix Engineering than what we are used to in these parts.
Mel
Follow Ups:
More advertising.
.
Edits: 07/29/14
nt
Isn't that one of the purposes of a message board? For people to share information about (in this case)records and vinyl playback equipment?
I'm a musician and release my cd's on my independent label. I've received quite a few very positive reviews. I am not allowed to post a link to them on AA. It would be fine for you or another inmate to post it, NOT for the manufacturer.
Edits: 07/29/14
.
Edits: 07/29/14 07/29/14
People here are interested in the product.
Is this really too hard for you to understand? Reviews of my cd's are in jazz publications, and are hardly affiliated with my label. Its an AA rule. I didn't write the rules, but I - and you - have to abide by them. I'd think it was obvious that they don't want the joint inundated with links to reviews posted by people who'd benefit from what amounts to advertising.FYI I might be interested in your product.
Edits: 07/29/14
.
Manufacturers will NEVER provide an objective evaluation of their products.
To be clear, I posted that video as a consumer. The "evaluation" was not by the manufacturer. It was actually my first attempt at any kind of a product evaluation (you'll see my other vids are mostly car stuff) - probably my last attempt, too! LOL Geez.
The manufacturer did jump in to add detailed information to Mel's questions/opinions. Can you blame a manufacturer for doing that?
Just more advertising.
.
Edits: 07/29/14
When logic fails, personal attacks begin.
I have no tagline. That was placed by the forum. I could make some suggestions for you as well, if I was going to waste any more time or bandwidth on your advertising.
Buh, bye
Hi Mel,
I should have probably led with the opinion that my VPI has never sounded so consistantly good since putting these devices into the chain. There is a certain rightness to everything I've dropped a needle on. "PRaT" is probably cliche, but I've noticed that the soundstage is very consistantly wide and instruments have a natural sound like they should.
Of course, I focused the video on the objective measurements, primarily because they told the story behind the improvement and consistancy in sound that I was experiencing. Seldom in the world of high end audio is there is objective measure that actually shows you why something sounds better to your ears.
I have no affiliation with Phoenix - I actually bought them through Hi-Fi Heaven on eBay. I love the VPI products, and will most likely eventually upgrade the Scout to another VPI table.
Drew,But what you said in your review, before being provoked, was that you couldn't say it made "a night and day difference." For the rest of us who could care less about bells and whistles, THAT was the review!
Edits: 07/29/14
I'm using a $55 variac with outstanding results. The biggest improvements in power to VPI tables seem to come from voltage reductions rather than speed control. I start at 110v and back down to 60v for playback. Sounds great at less than 1/10th the cost of these units.
It's the VOLTAGE that makes the biggest difference. Lower voltage smooths the synchronous pulses that get into the platter through the belt(s). Lower voltage means softer pulses, lower noise.
I've been telling people who call to get a Variac for probably 25 years! It really works but it will not stabilize the frequency like the SDS does if you are going for the last ounce of speed stability. A $100.00 metered Variac does a wonderful job on a synchronous motor table and for that matter it does a great job on power amps setting the voltage to the exact amount that sounds the best in your setup.
I run my big Mac amps at exactly 117V, sounds best that way.
HW
HW, does it do any damage to operate an Aries or TNT motor to operate at 60v after start-up at 110v? Doesn't seem to get warm or fail to hold speed.
As long as the motor locks on and stays synchronous you are fine. When it starts vibrating and going out of synch you are too low!!
Thanks, Harry. I'm very pleased with my Aries (extended) and the accompanying JMW-12 arm. And the variac made a nice improvement.
I have been using the Falcon PSU and Roadrunner unit for 3-4 months now with my VPI Scout with the 300 motor upgrade. I also very much recommend.Simple to use, you can see real time what the speed is doing.
I found Phoenix on the DIYAudio site, while keeping an eye on the K&K audio speed controller, which might be available now, and other DIY builds for turntable motor control. The Phoenix unit is like pushing the "easy" button, besides being very affordable.
Edits: 07/29/14
Post a Followup:
FAQ |
Post a Message! |
Forgot Password? |
|
||||||||||||||
|
This post is made possible by the generous support of people like you and our sponsors: