|
Audio Asylum Thread Printer Get a view of an entire thread on one page |
For Sale Ads |
70.197.1.161
In Reply to: RE: +1 nt. posted by henryrancourt@att.net on September 22, 2016 at 14:35:34
+1 means someone agrees with a post. You might consider reading "Transformer Protection-Mersen". It has calculations that differ somewhat in how conservative they are based on the current of the circuit. I myself don't see why one would require both primary and secondary fuses but I could be wrong. Maybe an EE can weigh in on this. T456
Follow Ups:
The primary fuse essentially protects the power transformer and everything downstream, as a last resort. Rail fuses protect, potentially, the output stage devices and the speakers. (Note that the OP states these are "fast-blow" types, which makes sense.) I have seen many commercially marketed amplifiers, both tube and solid state types, that are fused in this manner. (But I am definitely NOT an EE.)
Both my Atma-sphere amplifier (tube, OTL) and my Threshold amplifier (solid state) are doubly fused in this manner. On one occasion, a rail fuse blew in the Threshold because of a short at the output of that one channel, thus saving the entire amplifier from damage, as well as my delicate woofers.
Seems like a good answer. I guess you can't be too careful although it's hardly the case that all amps are fused in this way. It is still possible IME that the transformer primary fuse would or could protect the amp but of course not a likely as FB's on the rails. How did the short at the output come about?? (Not that I have never done it). The designers have their reasons but protection has it's price in sound quality. This does not mean that I am recommending something dangerous. T456
I think the negative effect on sound quality of using a fuse is way over-stated, most often on this website. I am not saying there is NO effect; I am saying that the effect is small and worth tolerating for the peace of mind that comes with using a proper fuse when and where necessary. But that's just my 2 cents.
On the Threshold, it was no big deal. The speaker wire ends very briefly touched each other, shorting hot to ground. That can have disastrous consequences if there is no fuse on the rail. In this case, no problem, except I needed to replace that one fuse.
I'm wondering why some have rail fuses and some don't. May have something to do with the cost of repair?? I'm glad my amp only has one, at least until if and when it blows for some reason. T456
and have explained why there are slow blow and fast blow fuses? Tweak, We all know you have your way of thinking on power amps, AC mains, and how everything bigger is better and the Engineers have another.If something ever does go wrong with your amp's output stage or power supply, you will wish you had all those fuses with proper values in place that you think are not necessary.
Edits: 10/04/16
There is only one fuse in my power amp. The value is the max value the designer "allows". Anyone "should" be able to hear that a bigger fuse sounds better and no fuse at all, a short, will sound the best ,IMHO. This is not to say anyone should do this but it does lay the ground work for the rational for bigger than necessary diodes to be used. Bigger solid state outputs will also sound better. A bigger power supply, bigger transformers, bigger cap banks, bigger wire will also sound better, not only in my opinion but the opinion of Nelson Pass. You might want to read what the engineer Nelson Pass has to says about power supplies and bigger. Also a bigger power supply will often if not always have a bigger , safely and appropriately installed, bigger fuse. A big problem companies have with bigger is the bigger cost . Big Tweaker
> > > Bigger solid state outputs will also sound better. A bigger power supply, bigger transformers, bigger cap banks, bigger wire will also sound better,
This is just wrong. No surprises here I guess.
I don't know what amplifier you own, but if you were to look inside, it's possible that the rails are fused internally (either with a conventional fuse that is not mounted on the exterior of the chassis or using just a fine wire) or that there is some sort of current-sensitive device in the circuit that is designed to blow before damage is done to the output devices.
99.9% certain that there are no internal fuses. Looked inside once over 3 tears ago. It sounds a bit odd that some other device other than a fuse would be used for the purpose of protection??? Fuses, like prophylactics have pleasure reduction built in to them. No doubt about it, necessary or not. Of course, always use the correct fuse. T456
There it is.
Warmest
Tim Bailey
Skeptical Measurer & Audio Scrounger
"The designers have their reasons but protection has it's price in sound quality. "
In the end there are trade-offs and everything is a compromise. One of my DIY amps had an output tube (KT-120,one of four) short plate to grid. Fortunately there was a 1K grid stopper that limited current so the secondary of the expensive interstage transformer feeding it wasn't damaged. Wasn't enough current draw to blow main fuse. The grid stopper did send up a smoke signal clueing me to the problem.
"It is better to remain silent and thought a fool, then speak and remove all doubt." A. Lincoln
I myself don't see why one would require both primary and secondary fuses but I could be wrong.
I agree. In fact if the primary winding overcurrent protection is fused correctly overloading the secondary will cause the primary fuse protection to blow.
Edits: 09/23/16
Post a Followup:
FAQ |
Post a Message! |
Forgot Password? |
|
||||||||||||||
|
This post is made possible by the generous support of people like you and our sponsors: