|
Audio Asylum Thread Printer Get a view of an entire thread on one page |
For Sale Ads |
141.239.172.61
In Reply to: RE: "few hundreds of mA, max." posted by Chip647 on July 19, 2016 at 05:07:44
This made me consider if the bias requirements might be different from a class AB PP amp. The bias supply is a seperate transformer 12.6v filament tranns wired backwards to a Schottky FWB which has a raw output of 70+volts. The bias supply consists of, 47uf x 70v film cap , ?H choke, 47 uf, to 14K , to balance pot, 10uf x 50v to G1 of 6550. The circuit is designed so that if the pot goes "open" there will be full -bias on the outputs instead on no bias. thanks for the suggestions, Dak
Follow Ups:
How many volts of negative bias are you running onto your grids? Seems like only a few are needed for Class "A" PP conduction.Say, bias voltage needed on grid is 2 VDC. With 1/2 watt:
144mA of current. You are going to need quite a bit heftier bias PS.
You can see, if you increase the watts of dissipation in the bias supply, which may need to be done --- the current flowing increases. Bad for grids.
2 VDC with 1 watt = 288 mA. Plus, you run a big risk of adding more noise to the system.
Is there a reason you are not using cathode biasing?
Thanks!
Edits: 07/19/16
Class A bias voltage is OTO -15V. The current flow is dictated by the resistance of the voltage dividers in the adjustment circuit( pots, etc ), and voltage across them. Plus a little for the grids.
Given it needs so little voltage, one could start with a lower voltage supply for sure. 70V is going to put you near the ends of the pot.
cheers,
Douglas
Friend, I would not hurt thee for the world...but thou art standing where I am about to shoot.
MY Av is 340 volts. I have the neg bias supply temporarily working with CRC supply of 300uf to 6k 2w to 300uf then to the bias supply divider resistors. It is the first section with the electrolytic caps and resistor that i would like to try the film caps and choke but i am unsure of the current capacity the choke should have. thanks for the help. dak
For -30VDC, 1/2-watt ---> 9.69mA
For -30VDC, 1-watt ---> 19.27mA
50mA capacity should be fine.
I will get the CLC installed and report back any significant results. cheers, Dak
Douglas, a lower voltage supply. But, may draw more current, right? At least compared to a (-40 to -60 VDC) bias supply --- for the same amount of wattage.For -15 VDC, at 1/2-watt = 19.2mA. Build a 50mA-100mA unit?
At 50-100mA, how much does background noise in the bias supply need to be addressed? Versus a 15-20mA bias supply. Prolly need a choke and a full-wave bridge.
Thanks
Edits: 07/20/16
Please describe this boas supply that is consuming this 19.2 mA? That is a little less than 1k at 15V( but that isn't the right voltage, we're dealing with the -30V supply ), that would be the total supply voltage applied to the top of the voltage divider( hopefully including at least one pot ). IOW, with a pair of 10k pots, one for each tube, we have a total bias supply resistance of 5k, or 6 mA flowing through it, plus the grid current( which will be much less than 6 mA ). 1 mA of grid current flowing through a 50k grid resistor gives us 50V...and that for sure isn't happening.Please explain where all this current is going.
cheers,
Douglas
Friend, I would not hurt thee for the world...but thou art standing where I am about to shoot.
Edits: 07/21/16
Post a Followup:
FAQ |
Post a Message! |
Forgot Password? |
|
||||||||||||||
|
This post is made possible by the generous support of people like you and our sponsors: