|
Audio Asylum Thread Printer Get a view of an entire thread on one page |
For Sale Ads |
96.83.99.105
In Reply to: RE: Monster HTS1600 power center - Unswitched outlets still only work with the power on? posted by centaurus3200 on August 14, 2016 at 14:35:43
The front panel has an LED for both the switched and unswitched outlets. Is the unswitched outlet LED lit? It should light when the units AC Power cord is plugged in. The power switch makes the switched couplet LED light up.
Your move
ET
"If at first you don't succeed, keep on sucking till you do suck seed" - Curly Howard 1936
Follow Ups:
well, i hooked it up anyway. there's only 2 components i want on all the time (preamp and cd player), so i plugged those into my old panamax power strip. and two components i need to turn on and off (McIntosh MC60 monoblocks). the rest i don't care if they aren't on all the time.
i'm always surprised when i notice a difference in sound... just by plugging stuff into a different power strip. the stereo has an obvious amount more top end (Yamaha NS-1000M) and just seems ore ballsy.
i'm no engineer, but i think this is because i previously plugged EVERYTHING into my 20+ year old adcom ACE-515 "a/c enhancer". it had one unswitched outlet, which i plugged said panamax power strip into. i'm thinking the adcom's component specs drifted over time and probably lowered the voltage and current? no idea...
see ya,
Robby
Are the switched outlets REALLY switched or is their a RELAY which could be stuck or wired permananently ON?
The switch would be a heavy duty unit while for switching a relay, a more modest switch would suffice. Though the relay would still be required to have 15amp or 20amp capacity.
Too much is never enough
Yes the unswitched are for digital not higher current items but he is also saying no LED on the panel for switched or unswitched too.
ET
"If at first you don't succeed, keep on sucking till you do suck seed" - Curly Howard 1936
I guess what I mean to say is that I can think of only 2 reasons for the 'switched' outlets to no longer be switchable.
Modification of Equipment. Moving ONE wire from one side of the switch / relay to the OTHER would do this
OR
Stuck Relay. The low-current switch is still OK, and unmodified, BUT the relay is stuck 'on'. A good zap COULD 'weld' the contacts.
If such a relay is socketed, it takes all of 10 seconds to replace.
Too much is never enough
these are all the lights i see on the front panel.
i did pop the top on it. i'm no engineer, but it looks like all outlets are switched.
it's fine, i think i can use it for now and use my ancient panamax power strip for my unswitched stuff. then, just keep an eye out for something more suitable.
I have owned a couple of Monster items, and messed around with them. I would think plenty of owners do.
It would be relatively easy ?? to change them around. Jut run them all through the switch.
The wiring in them usually is pretty easy to follow.. So look at the supposedly non switched outlets and see if maybe their wiring was moved?
Is there a wiring block on or near the circuit board(s) which is not used?
Typically the wires come from the board, end at a small screw block, then go to the duplex on back.
Then the unswitched would go through that switch which would be bad for a few reasons. The unswitched are made for digital gear anyway though so they would be lower current. The power amp should be plugged into the audio outlets and they are switched. Also KAHL Audio is printed on his unit. Maybe they modded it or something. I would call them. They are a dealer.
ET
"If at first you don't succeed, keep on sucking till you do suck seed" - Curly Howard 1936
Edits: 08/18/16
Running a power amp through the puny switched circuit relay/switch.
I agree it is a bad idea.
The previous owner may have never used the unit for a power amp anyway!
Post a Followup:
FAQ |
Post a Message! |
Forgot Password? |
|
||||||||||||||
|
This post is made possible by the generous support of people like you and our sponsors: