Home
AudioAsylum Trader
Bottlehead Forum

Welcome! Need support, you got it. Or share you ideas and experiences.

For Sale Ads

FAQ / News / Events

 

Use this form to submit comments directly to the Asylum moderators for this forum. We're particularly interested in truly outstanding posts that might be added to our FAQs.

You may also use this form to provide feedback or to call attention to messages that may be in violation of our content rules.

You must login to use this feature.

Inmate Login


Login to access features only available to registered Asylum Inmates.
    By default, logging in will set a session cookie that disappears when you close your browser. Clicking on the 'Remember my Moniker & Password' below will cause a permanent 'Login Cookie' to be set.

Moniker/Username:

The Name that you picked or by default, your email.
Forgot Moniker?

 
 

Examples "Rapper", "Bob W", "joe@aol.com".

Password:    

Forgot Password?

 Remember my Moniker & Password ( What's this?)

If you don't have an Asylum Account, you can create one by clicking Here.

Our privacy policy can be reviewed by clicking Here.

Inmate Comments

From:  
Your Email:  
Subject:  

Message Comments

   

Original Message

RE: Single Ended eXperimenter's Kit for headphones

Posted by Paul Joppa on October 15, 2009 at 10:33:11:

I'd like to take this opportunity to expand on Doc B's comments (with which I fully agree).

The IHF standard calls for a 5vRMS source with 120 ohms impedance. This is supposed to be applicable to all headphones. It will produce maximum power into a 120 ohms headphone; that power is volts squared over resistance, in this case 0.052 watts. At the extremes of 600 ohm phones, or 24 ohm phones the available power is less, 0.029 watt. So for a tube amp capable of delivering 0.05 watts (50 milliwatt or mW) an output transformer with taps for the various headphone impedances in the range of 24 to 600 ohms would be appropriate, in order to preserve an appropriate load on the tube to keep distortion low.

As the available amp power increases, transformers with lower impedance outputs will be able to supply the necessary voltage. Used in this way, the amplifier always sees a high impedance load and distortion is kept low. At the same time, the noise voltage is reduced by the lower impedance output tap. For more information on this issue, look at the Bottlehead Community page; my white paper on signal and noise levels is near the top. The SEX amp produces 2 watts, which is 4vRMS, on the 8 ohm transformer tap loaded with a speaker. With the standard 120 ohm series resistor it can produce 5 vRMS easily, thus meeting the IHF standard accurately and with a very low noise floor.

There is a 500 ohm tap available on the stock autoformer. However, it would produce over 30 volts into a set of headphones, far too much for the phones or your ears to handle.

Now admittedly the IHF standard is old, and specifically it predates the widespread use of headphones with portable devices like iPods. These devices run on low voltages, and in order to obtain sufficient loudness the headphones need to be low impedance and highly sensitive. Some of these headphones do not work at their best with the IHF standard 120 ohm source impedance, being designed for a near zero source impedance and low voltages (around 1vRMS is not uncommon). Unfortunately, few headphone manufacturers will tell you this. But if you do have such a set of phones, the ideal would be a low-impedance source of even lower voltage - in other words, for the SEX amp a tap of less than 1.0 ohms, with no series resistor. It is easy enough to modify the 120 ohm series resistor to an L-pad which will reduce the output voltage and impedance for such phones, though I don't think we have documented such a modification yet. It would merely involve changing the 120 ohm resistor for another value, and adding another resistor from the "hot" headphone signal to ground. I would suggest 6.8 ohms (5 watt) and 1.2 ohms (1 watt) as widely available and suitable starting values.

I hope that helps clarify the situation.