Vinyl Asylum Welcome Licorice Pizza (LP) lovers! Setup guides and Vinyl FAQ. |
|
In Reply to: Because God gave us TT mats :-) posted by bare on October 23, 2016 at 10:48:02:
bare: "Ream out your LP centers and fit a bit of silicone ring/tube as an Isolator so the lp never directly contacts the spindle..."
Clever. I like the way you think. :)
This post is made possible by the generous support of people like you and our sponsors:
Follow Ups Full ThreadTopic - Why turntable bearing shaft and spindle machined as one piece? - caligari 10:16:12 10/23/16 (50)
- Is there any one out there that knows physics??? - TomWh 10:41:55 10/25/16 (1)
- RE: Is there any one out there that knows physics??? - caligari 11:23:12 10/25/16 (0)
- RE: Why turntable bearing shaft and spindle machined as one piece? - Lew 07:25:54 10/24/16 (6)
- RE: Why turntable bearing shaft and spindle machined as one piece? - caligari 08:26:37 10/24/16 (5)
- RE: Why turntable bearing shaft and spindle machined as one piece? - Plato65 01:00:10 10/25/16 (1)
- RE: Why turntable bearing shaft and spindle machined as one piece? - caligari 16:43:40 10/25/16 (0)
- The Bergmann idea is certainly not novel - Lew 10:37:44 10/24/16 (2)
- RE: The Bergmann idea is certainly not novel - caligari 11:07:23 10/24/16 (1)
- RE: The Bergmann idea is certainly not novel - thekong 23:21:07 10/24/16 (0)
- RE: Why turntable bearing shaft and spindle machined as one piece? - Victor7 05:16:46 10/24/16 (0)
- RE: Why turntable bearing shaft and spindle machined as one piece? - Hiendmuse 02:30:52 10/24/16 (3)
- RE: Why turntable bearing shaft and spindle machined as one piece? - John Elison 04:59:18 10/24/16 (2)
- RE: Why turntable bearing shaft and spindle machined as one piece? - Hiendmuse 07:36:02 10/24/16 (1)
- Okay! Thanks! /nt\ - John Elison 08:42:27 10/24/16 (0)
- RE: Many such designs might be possible... - mr.bear 16:52:05 10/23/16 (2)
- RE: Many such designs might be possible... - caligari 18:00:19 10/23/16 (1)
- Clamp or no? - mr.bear 20:26:13 10/23/16 (0)
- 'IF" - genungo 14:51:28 10/23/16 (0)
- RE: Why turntable bearing shaft and spindle machined as one piece? - bcowen 14:12:17 10/23/16 (7)
- Most turntable thrust bearings - Penguin 21:04:48 10/23/16 (6)
- RE: Most turntable thrust bearings - bcowen 15:30:16 10/24/16 (5)
- It is just a matter of magnitude.... - Penguin 18:38:51 10/24/16 (3)
- Another measure - rrob 03:39:08 10/25/16 (2)
- before chasing geese - Penguin 06:42:41 10/25/16 (1)
- RE: before chasing geese - rrob 11:26:22 10/25/16 (0)
- RE: Most turntable thrust bearings - John Elison 17:11:15 10/24/16 (0)
- RE: Why turntable bearing shaft and spindle machined as one piece? - John Elison 13:45:26 10/23/16 (6)
- RE: Why turntable bearing shaft and spindle machined as one piece? - caligari 14:13:24 10/23/16 (5)
- RE: Why turntable bearing shaft and spindle machined as one piece? - John Elison 15:07:09 10/23/16 (4)
- RE: Why turntable bearing shaft and spindle machined as one piece? - caligari 15:35:57 10/23/16 (3)
- RE: Why turntable bearing shaft and spindle machined as one piece? - Tre' 17:47:07 10/23/16 (0)
- RE: Why turntable bearing shaft and spindle machined as one piece? - John Elison 17:12:49 10/23/16 (1)
- RE: Why turntable bearing shaft and spindle machined as one piece? - caligari 17:57:46 10/23/16 (0)
- RE: Why turntable bearing shaft and spindle machined as one piece? - markinuk 13:10:45 10/23/16 (1)
- RE: Why turntable bearing shaft and spindle machined as one piece? - bjh 17:43:04 10/24/16 (0)
- Concentricity - Mossback 11:16:13 10/23/16 (7)
- Old machinist... - mosin 16:02:34 10/23/16 (6)
- Foolish Speculations.. - bare 16:52:50 10/23/16 (5)
- RE: Foolish Speculations.. - mosin 17:59:15 10/23/16 (4)
- RE: Foolish Speculations.. - caligari 21:40:49 10/23/16 (0)
- The quietest bearing ever implemented is using some of the hardest materials - Penguin 18:20:59 10/23/16 (2)
- RE: The quietest bearing ever implemented is using some of the hardest materials - mosin 06:55:23 10/27/16 (1)
- Do not really know the reason why, but - Penguin 07:35:24 10/27/16 (0)
- RE: Why turntable bearing shaft and spindle machined as one piece? - caffeinator 10:37:07 10/23/16 (6)
- RE: Why turntable bearing shaft and spindle machined as one piece? - caligari 11:46:03 10/23/16 (0)
- Because God gave us TT mats :-) - bare 10:48:02 10/23/16 (4)
- Why not just machine down the spindle - Penguin 14:46:13 10/23/16 (1)
- As markinuk mentioned above, Roksan does just that - 1973shovel 18:28:39 10/23/16 (0)
- 'At's an awful lot o' reamin'... - genungo 11:29:44 10/23/16 (0)
- RE: Because God gave us TT mats :-) - caligari 11:28:01 10/23/16 (0)
Follow Ups
- RE: Because God gave us TT mats :-) - caligari 11:28:01 10/23/16 (0)