|
Tubes Asylum Questions about tubes and gear that glows. FAQ |
|
|
|
Tubes Asylum Questions about tubes and gear that glows. FAQ |
|
In Reply to: Not sure about pin-outs posted by FenderLover on August 7, 2015 at 23:40:22:
I'm starting over using 12ax7's also using a 230v isolation transformer that is the 12ax7 schematic but I've seen there is a fault on the schematic at v1b the cathode and plate are the wrong way around according to the pin out of a 12ax7
This post is made possible by the generous support of people like you and our sponsors:
Follow Ups
- RE: Not sure about pin-outs - kylealers@gmail.com 23:56:22 08/07/15 (42)
- Maybe the schemo started to compensate for the 5670? - FenderLover 06:59:03 08/08/15 (41)
- RE: Maybe the schemo started to compensate for the 5670? - kylealers@gmail.com 07:43:04 08/08/15 (40)
- No... 5670 is 6.3VAC in series - FenderLover 18:24:41 08/08/15 (39)
- RE: No... 5670 is 6.3VAC in series - kylealers@gmail.com 00:01:50 08/09/15 (38)
- RE: No... 5670 is 6.3VAC in series - FenderLover 07:23:58 08/09/15 (37)
- RE: No... 5670 is 6.3VAC in series - kylealers@gmail.com 22:54:25 08/09/15 (36)
- Wait... didn't this pre-amp work before? - FenderLover 00:51:54 08/10/15 (35)
- RE: Wait... didn't this pre-amp work before? - kylealers@gmail.com 01:25:02 08/10/15 (0)
- RE: Wait... didn't this pre-amp work before? - kylealers@gmail.com 01:06:08 08/10/15 (33)
- You can hook the 12AX7 in parallel, using that heater tap - FenderLover 01:36:50 08/10/15 (32)
- RE: You can hook the 12AX7 in parallel, using that heater tap - kylealers@gmail.com 09:15:14 08/10/15 (0)
- RE: You can hook the 12AX7 in parallel, using that heater tap - kylealers@gmail.com 08:33:28 08/10/15 (30)
- No... all you need is one 6.3VAC or 6.3VDC source - FenderLover 15:02:41 08/10/15 (29)
- RE: No... all you need is one 6.3VAC or 6.3VDC source - kylealers@gmail.com 22:25:24 08/10/15 (28)
- You are welcome. - FenderLover 23:15:48 08/10/15 (27)
- RE: You are welcome. - kylealers@gmail.com 02:06:41 08/11/15 (25)
- Look for a good silverface Dual Showman to restore - FenderLover 07:34:44 08/11/15 (24)
- RE: Look for a good silverface Dual Showman to restore - kylealers@gmail.com 08:00:50 08/11/15 (22)
- There aren't many good DIY amp kits in that power range - FenderLover 08:05:56 08/11/15 (21)
- RE: There aren't many good DIY amp kits in that power range - kylealers@gmail.com 08:53:25 08/11/15 (20)
- Sure... - FenderLover 09:44:08 08/11/15 (19)
- RE: Sure... - kylealers@gmail.com 09:52:22 08/11/15 (17)
- None at all - FenderLover 13:57:31 08/11/15 (16)
- RE: None at all - kylealers@gmail.com 12:17:55 08/12/15 (14)
- Yes, only if you are going to use the tap in AC form - FenderLover 22:30:34 08/12/15 (13)
- RE: Yes, only if you are going to use the tap in AC form - kylealers@gmail.com 22:39:15 08/12/15 (12)
- 100-ohm or 220-ohm will be fine. - FenderLover 00:20:44 08/13/15 (11)
- RE: 100-ohm or 220-ohm will be fine. - kylealers@gmail.com 02:31:50 08/13/15 (9)
- Cool! - FenderLover 07:13:20 08/13/15 (8)
- RE: Cool! - kylealers@gmail.com 03:35:28 08/14/15 (7)
- center tap - FenderLover 07:15:02 08/14/15 (6)
- RE: center tap - kylealers@gmail.com 01:44:30 08/15/15 (5)
- How did you want to "better" your PSU? - FenderLover 07:36:24 08/15/15 (4)
- RE: How did you want to "better" your PSU? - kylealers@gmail.com 08:08:55 08/15/15 (3)
- RE: How did you want to "better" your PSU? - FenderLover 08:38:36 08/15/15 (2)
- RE: How did you want to "better" your PSU? - kylealers@gmail.com 02:33:38 08/16/15 (1)
- RE: How did you want to "better" your PSU? - FenderLover 03:54:12 08/16/15 (0)
- BTW... - FenderLover 00:21:58 08/13/15 (0)
- You need to know... - FenderLover 06:35:22 08/12/15 (0)
- Layout link - FenderLover 09:46:09 08/11/15 (0)
- DS schematic - FenderLover 07:41:26 08/11/15 (0)
- Portaflex B15N - FenderLover 23:18:35 08/10/15 (0)
Top of Page ]
[ Contact Us ]
[ Support/Wish List ]
[ Copyright © 2024, Audio Asylum, all rights reserved ]
