Tubes Asylum Questions about tubes and gear that glows. FAQ |
|
In Reply to: Either one piece bridge or four diodes should be fine posted by FenderLover on August 2, 2015 at 09:35:45:
You mean 230VAC to 12VAC to 230VAC? I used the two back to back tranny's. Bacuase I was able to find them locally and much much cheaper. Might this cause problems? Because that's the power supply schematic that goes with the pre amp schematic
This post is made possible by the generous support of people like you and our sponsors:
Follow Ups
- RE: Either one piece bridge or four diodes should be fine - kylealers@gmail.com 10:02:01 08/02/15 (54)
- Sorry... 230VAC - FenderLover 14:08:23 08/02/15 (53)
- RE: Sorry... 230VAC - kylealers@gmail.com 22:52:09 08/02/15 (52)
- Voltage on plates and cathode will change... - FenderLover 00:29:52 08/03/15 (51)
- RE: Voltage on plates and cathode will change... - kylealers@gmail.com 00:57:35 08/03/15 (50)
- Microphonics - FenderLover 05:00:04 08/03/15 (49)
- RE: Microphonics - kylealers@gmail.com 07:05:24 08/03/15 (48)
- RE: Microphonics - FenderLover 14:42:36 08/03/15 (47)
- RE: Microphonics - kylealers@gmail.com 23:45:01 08/04/15 (46)
- Cathode-tied resistor - FenderLover 04:22:37 08/05/15 (45)
- RE: Cathode-tied resistor - kylealers@gmail.com 01:11:36 08/07/15 (44)
- Not sure about pin-outs - FenderLover 23:40:22 08/07/15 (43)
- RE: Not sure about pin-outs - kylealers@gmail.com 23:56:22 08/07/15 (42)
- Maybe the schemo started to compensate for the 5670? - FenderLover 06:59:03 08/08/15 (41)
- RE: Maybe the schemo started to compensate for the 5670? - kylealers@gmail.com 07:43:04 08/08/15 (40)
- No... 5670 is 6.3VAC in series - FenderLover 18:24:41 08/08/15 (39)
- RE: No... 5670 is 6.3VAC in series - kylealers@gmail.com 00:01:50 08/09/15 (38)
- RE: No... 5670 is 6.3VAC in series - FenderLover 07:23:58 08/09/15 (37)
- RE: No... 5670 is 6.3VAC in series - kylealers@gmail.com 22:54:25 08/09/15 (36)
- Wait... didn't this pre-amp work before? - FenderLover 00:51:54 08/10/15 (35)
- RE: Wait... didn't this pre-amp work before? - kylealers@gmail.com 01:25:02 08/10/15 (0)
- RE: Wait... didn't this pre-amp work before? - kylealers@gmail.com 01:06:08 08/10/15 (33)
- You can hook the 12AX7 in parallel, using that heater tap - FenderLover 01:36:50 08/10/15 (32)
- RE: You can hook the 12AX7 in parallel, using that heater tap - kylealers@gmail.com 09:15:14 08/10/15 (0)
- RE: You can hook the 12AX7 in parallel, using that heater tap - kylealers@gmail.com 08:33:28 08/10/15 (30)
- No... all you need is one 6.3VAC or 6.3VDC source - FenderLover 15:02:41 08/10/15 (29)
- RE: No... all you need is one 6.3VAC or 6.3VDC source - kylealers@gmail.com 22:25:24 08/10/15 (28)
- You are welcome. - FenderLover 23:15:48 08/10/15 (27)
- RE: You are welcome. - kylealers@gmail.com 02:06:41 08/11/15 (25)
- Look for a good silverface Dual Showman to restore - FenderLover 07:34:44 08/11/15 (24)
- RE: Look for a good silverface Dual Showman to restore - kylealers@gmail.com 08:00:50 08/11/15 (22)
- There aren't many good DIY amp kits in that power range - FenderLover 08:05:56 08/11/15 (21)
- RE: There aren't many good DIY amp kits in that power range - kylealers@gmail.com 08:53:25 08/11/15 (20)
- Sure... - FenderLover 09:44:08 08/11/15 (19)
- RE: Sure... - kylealers@gmail.com 09:52:22 08/11/15 (17)
- None at all - FenderLover 13:57:31 08/11/15 (16)
- RE: None at all - kylealers@gmail.com 12:17:55 08/12/15 (14)
- Yes, only if you are going to use the tap in AC form - FenderLover 22:30:34 08/12/15 (13)
- RE: Yes, only if you are going to use the tap in AC form - kylealers@gmail.com 22:39:15 08/12/15 (12)
- 100-ohm or 220-ohm will be fine. - FenderLover 00:20:44 08/13/15 (11)
- RE: 100-ohm or 220-ohm will be fine. - kylealers@gmail.com 02:31:50 08/13/15 (9)
- Cool! - FenderLover 07:13:20 08/13/15 (8)
- RE: Cool! - kylealers@gmail.com 03:35:28 08/14/15 (7)
- center tap - FenderLover 07:15:02 08/14/15 (6)
- RE: center tap - kylealers@gmail.com 01:44:30 08/15/15 (5)
- How did you want to "better" your PSU? - FenderLover 07:36:24 08/15/15 (4)
- RE: How did you want to "better" your PSU? - kylealers@gmail.com 08:08:55 08/15/15 (3)
- RE: How did you want to "better" your PSU? - FenderLover 08:38:36 08/15/15 (2)
- RE: How did you want to "better" your PSU? - kylealers@gmail.com 02:33:38 08/16/15 (1)
- RE: How did you want to "better" your PSU? - FenderLover 03:54:12 08/16/15 (0)
- BTW... - FenderLover 00:21:58 08/13/15 (0)
- You need to know... - FenderLover 06:35:22 08/12/15 (0)
- Layout link - FenderLover 09:46:09 08/11/15 (0)
- DS schematic - FenderLover 07:41:26 08/11/15 (0)
- Portaflex B15N - FenderLover 23:18:35 08/10/15 (0)