|
Audio Asylum Thread Printer Get a view of an entire thread on one page |
For Sale Ads |
74.96.191.12
In Reply to: RE: Atmasphere MA-2 impedance question posted by tyu on June 03, 2012 at 08:47:49
None of us, not even Will, has deleted the mixer box, which as you know contains two capacitors, one each in series with each arm of the secondary of the treble transformer. I don't think it would be safe to do that. But as you note, I found and purchased some Russian 8kV .01uF teflon film caps on eBay, and I have used those to replace the stock .015uF caps that are used by SL. IMO, the Russian caps sound better than the OEM ones.
Also, Will deleted the inductor in series with the SL bass transformer; I did not do that. I use a 1.5mH 12ga copper Alphacore air core ribbon inductor on the input side of the SL bass transformer.
Follow Ups:
Thanks lew...it all good..you can were my time goes... just liveing with this everday...
This is the type of sound that makes me get up in the middel of the night...to see if it still there....it been 4days now..... i still cant beleve it....
As you know the Acoustat panels are 9"x 48" so i can add as minny as i like...the base lode for the tranfourmers i have found is 3ea pr side... thay are so well made that thay dont even have to have a frame ...thay can just be setup ezely....i have found the best sound is with a flat setup...like the Quad 57s...so now i am driving this setup with the M60..
It well play as loude as if thay were Klipsch..go figg...like you sead in a post i read..this is the sound i been looking for for 40years...
So if we look at the Acoustat 121 interface in this setup the 50k on the base tranfourmer secdary ...is like your induckter....an i have now on the high frc. tranfourmer the two .0015 6k oil caps...were there was the stock .01 5k caps....
One thing you may tell your frinds on the soundlabe site is this setup well work with the stock high frc.tranfourmers...this would let them see what a great setup this is...then thay can get the new tranfourmers if thay feel that thay need them....to test this just put a fuse in the high frc primary side an uses a 3amp...i did this on my stock high frc. tranfourmer an did not kill one fuse....Great fun....60tube watts goodluck
So, before Will first contacted me by email to tell me about the Australian transformers, I was wondering whether I could even just remove that parallel resistor in the hi-pass filter for the OEM SL treble toroid. Dr. West had repeatedly warned against doing that, for reasons having to do with the toroid, but it was clear to me that the major problem with driving the SL speakers using my OTLs had to do with that resistor. In fact, Will reported to me that he did remove the parallel resistor successfully in his early experiments, and upon hearing that he got away with it, I did the same, while waiting for the new transformers to get to me from Australia. You are quite correct; it's a big improvement vs with the resistor in place. What I did also was to reduce the series capacitance to 22uF so as not to change the -3db point of the hi-pass filter. (Accounting for the intrinsic impedance of the speaker at the crossover point, 22uF gives about the same "knee" as does 36uF plus the 8-ohm parallel resistor.) I think Will completely removed that capacitor on the primary of the toroid; I cannot recall what he said about that. I did not try it.
Edits: 06/04/12
Hi Lew,
By any chance you would have the schematics for the AU90 mods?
Post a Followup:
FAQ |
Post a Message! |
Forgot Password? |
|
||||||||||||||
|
This post is made possible by the generous support of people like you and our sponsors: